Tuesday 29 March 2016

Madbean Wigl (Vibe)

Brian's take on John Hollis Easyvibe.
You can find his 1590G size boards on his website.
Check his original notes here for more infos on how to build this project!



 Here is another version with Mark Hammer's anti-ticking mod as suggested by Ciaran:



51 comments:

  1. How would this compare with the ROG tri-vibe ?

    ReplyDelete
  2. there is a you tube video of all 8 of the 1590g builds . This sounds fantastic . its got a really great univibe warble and throb. Thanks Alex for doing this one .ill verify it this weekend or sooner.

    ReplyDelete
  3. Thanks mate!
    I've added the video.

    ReplyDelete
    Replies
    1. Excellent! I figure that you'll have all nine projects done soon, so I make them all and mount them in a single enclosure for the ultimate pedalboard! ;)

      (Actually there is a verified layout for the Moar pedal in the forum).

      Delete
  4. well i cant get the lfo to work. i have checked everything several times .. i must have a bad part idk. i might try building it from scratch again. it only took three hours to build and i have 4 in troubleshooting. i got 1.11 volts instead of four and none if the chip legs that are supposed to varie are .

    ReplyDelete
    Replies
    1. there is a problem with the Vb.try to take a wire from D4-10k-10uf line, and wire it somewhere under tl062 where pin2 and 5 connect

      Delete
    2. or just disolder the right long link, and made other 2 with a double link next to D4 and 10k

      Delete
  5. Well spotted Savvas!
    There should have been a double link there.
    It's been corrected.

    ReplyDelete
  6. thanks guys ill try that. im on build 80 right now. i looked at the schematic several times and knew something was up i cant believe i missed it too. Thanks Alex and Savvas

    ReplyDelete
  7. ok i added the double link. i now have 4.1 volts where need be but i get no flash on the lfo no pulse. just a steady red light. i have now checked this board a dozen times. is it possible the original configuration damaged a part? is it possible we still have another issue with the layout? please look it over for me one more time . i cant wait to get this one going .

    ReplyDelete
  8. Checked it again and I'm pretty sure the layout matches the scheamatic. I doubt something got damaged cause of the missing double link but... Is D3 not pulsing or the Rate LED?
    Have you try changing the ICs?
    What are your voltages?

    ReplyDelete
  9. Tag it lad.

    Sounds great. Very chewy. Getting some ticking but I'm using a 072 as a temp sub. I'll try a 062 when they land and report back.

    Ramp up is slower than ramp down (triangle wave) so it gets a bit sea sick at higher rates. Currently going through LDR's but I think I'm settling on NSL19.

    I have to say I like this much better than the ROG tri-vibe. I only ever used the univibe setting on it anyway and found it tame enough. This has much more bite to it...and it fits in a B box!

    Cheers yet again!

    Strasser.....i found that the trimmer has a definite small sweet spot where the pulse is full light/dark. Either side of that and it makes subtle pulses. Also with the depth fully CCW there is no pulse at all. Maybe look here for your problem? I also had to reflow my IC sockets before it kicked in.

    ReplyDelete
    Replies
    1. thanks Ciaran I played with it to no avail. I may just scrap this and start over I can do it in less than 3 hours and I have way more than that troubleshooting ha ha. I may have a bad part somewhere idk

      Delete
  10. Cool!
    Thanks Ciaran!
    TL062 should be quiter.

    ReplyDelete
  11. the top right 100n was bad . i didnt do a continuity check because i had no bridges . once i did a continuity check i discovered it. figures the first time i use greenies to save a little money and i paid the price. i guess ill never use a greenie again without checking it first ha ha.that cost me two hours last night and a half an hour tonight. Brand new bad will kill ya. to late to plug it in for a demo and tweaking but voltages are all good and i have a pulse. thanks guys . im sure its good to go now. you guys rock I appreciate it. i knew i had a bad part even the other night before the VB fix.what are the odds? i have had one bad resistor and now one bad cap in 80 builds. the worst was the counterfit ca3080a i got . i spent three nights trying to figure out why my dyna comp wouldnt work.

    ReplyDelete
    Replies
    1. Great news Strasser! When you get a chance to listen can you report back on ticking? I used a TL072 and I'm waiting for a 062. I'm preparing myself to modify my build to include Mark Hammers ticking solution....if I need to that is.

      Delete
    2. It is great news thank God that bad cap showed up as continuity. I was snowblind from checking that board three nights in a row . Ill fire it up tonight for sure. I had a ticking issue with the boss Ce-2 chorus here and Frank_NH helped he redid the layout so I was getting separate power for the lfo. Thats in the forum under boss ce-2 ticking. Where can I read about Mark Hammers ticking solution? I have a tl062 and I have tl022 if need be Ill let you know. Man I really hope this doesn't tick I have way to many hours in this one already ha ha.

      Delete
    3. Mark Hammer solution in a nutshell....isolate LFO IC power from the rest (basically install a 100r resistor between 9V and pin 8. The rest of the board gets 9V before said resistor.

      Install a small filter cap 4u7 to 10u on LFO IC power to ground to act as a reservoir for the LFO current rush.

      So I replaced my 072 with a 062 and the ticking dramatically reduced. Did the mods listed above and its practically gone! Still ticks with hi gain circuits but for my purposes its near silent. Result!

      Cheers lads

      Delete
    4. Hi Ciaran,
      I've added a version with the anti-ticking mod:
      is that what you've meant?

      Delete
  12. its all working really well. it has a faint tick/pulse. i can live with it. i tried the tl022 didnt make any difference.the tl062 is fine. this is a great univibe pedal. i compared next to both my madbean harbinger uni vibes one on pcb and one on the tag oard layout and it was different but just as cool in its own right.there is a tad volume drop and its a little bright. i love phasers and vibes. i might do a full 4 stage easy vibe someday. Thanks Alex Savvas and Ciaran. you guys rock! next project the ping

    ReplyDelete
  13. Hey Ciaran, could you show me were to put the small filter cap from ic lfo power to ground. I have added the 100R, just not sure were to put the cap. Thanks.

    ReplyDelete
    Replies
    1. What I did was...

      Replace the link next to the TL062 with a 100r
      Move 9V wire to row below Rate 2
      Removed the 4k7 at LED+ (I used the Rate LED as an on indicator as well)
      Add a link from the 10u cathode to old 9V row.
      Replace the protection diode with the small filter cap. Anode to top row, cathode to Row 4. I don't use polarity protection so I removed the diode just to have space for the cap.

      Where is your 100r placed at the minute?

      Delete
    2. I put the 100r from the top right hole to the same hole as the 9v input, but your solution looks easier so i will do that.

      Delete
    3. OK done. Thanks Cairan. Kept the 4k7 and LED in place by placing insulated wire from 10u cathode to old 9v so could still have indicator LED. Nice vibe. I used the bog standard LDRs from Bitsbox and they seem to work fine.

      Delete
  14. How about the full easy vibe with the anti ticking??

    ReplyDelete
  15. Hey how bad was yours ticking mine isnt that bad.Its not perfect but you couldnt hear it while playing . is it perfect now?

    ReplyDelete
  16. Hey how bad was yours ticking mine isnt that bad.Its not perfect but you couldnt hear it while playing . is it perfect now?

    ReplyDelete
    Replies
    1. It wasn't bad at all. But since doing the isolation trick above its now silent when playing clean and near silent with high gain. A definite improvement for me anyway.

      Delete
    2. Thanks Ill have to mod it then we want perfection if attainable

      Delete
  17. i just modded my first layout to the second and lost my pulse .

    ReplyDelete
    Replies
    1. unless i have another bad part i dont think version 2 is right.

      Delete
    2. Did you get all the cuts? The cut under IC1 Pin 5 is now replaced with a link. Missing that would break the LFO

      Delete
    3. hmm i left that little part the way it was since there is a hole were the link would go so i put a solder bridge from pin 5 to the row below so its still seperated going right to left the original cut is still blocking and the solder bridge is my link That should work right?

      Delete
  18. Thanks a lot for this layout, it's a great sounding vibe. I build the version 2 with the mod, I used a TL062 and a 10uF for C1 and it works like a charm. I didn't use it a lot for the moment but I didn't hear ticking sound.
    For me it's can be tag verified.

    Thanks a lot for all the work.

    ReplyDelete
  19. Thanks a lot for this layout, it's a great sounding vibe. I build the version 2 with the mod, I used a TL062 and a 10uF for C1 and it works like a charm. I didn't use it a lot for the moment but I didn't hear ticking sound.
    For me it's can be tag verified.

    Thanks a lot for all the work.

    ReplyDelete
  20. Thanks Thomas I am glad you verified it . I must have a mistake on the mod from build one to build 2. Sorry alex ha ha.

    ReplyDelete
  21. Thanks Thomas I am glad you verified it . I must have a mistake on the mod from build one to build 2. Sorry alex ha ha.

    ReplyDelete
  22. Maybe easier to build version 2 directly (what I did) than converting version 1.

    ReplyDelete
    Replies
    1. well i let it sit for a week. found the issue in ten seconds when i came back. i forgot to bridge the original cut under d9. I stared at it too long the other night.I cant tell you how many times i have come back with fresh eyes and ideas and figured stuff out. in just a few moments . its always a good idea to stop troubleshooting once you start to get frustrated.Thanks Alex the tic is even less than the little i had on build one

      Delete
    2. Cool!
      I'm glad you've managed to fix it! :)

      Delete
  23. I bought some VTL5C3/2 vactrols by mistake a while back (they have 3 LDR terminals instead of the usual 2 - datasheet at http://www.excelitas.com/downloads/dts_vtl5c2232.pdf). Anyway, this circuit works really well using one of these with the centre tap LDR going to the common (lower strip) connection. Probably just as easy to roll your own ldr/led/ldr combo, but it's an alternative if you have a vtl5c3/2 to hand.

    ReplyDelete
  24. Hi , Does the Madbean version have a stronger un vibe sound then the John Hollis build , or are there pretty much the same.

    ReplyDelete
  25. I am a bit lost , the Rate+ LED Wire and LED+ on the board ,where do I run wires . Can I connect them both stomp switch .

    ReplyDelete
    Replies
    1. The best way is to run both -ve ends to the stompswitch. But if you want the rate LED on all the time even when pedal is bypassed then run its -ve to ground.

      Delete
  26. This comment has been removed by the author.

    ReplyDelete
  27. I am getting no vibe whatsoever and I have low output and its very distorted, I've built the second version, anyone had similar problems?

    ReplyDelete
    Replies
    1. Must be a mistake I made, just build the first layout from scratch and it sounds AMAZING.

      Delete
  28. Hello, I made the 2nd version. It has low output and distorted. Also I opened the covered led and ldr and noticed that the led is always on even when I don't play. Where do you think I should look for any faults/mistakes I might have made? Gonna probe this later too. Thanks.

    ReplyDelete