Here's a collection of vero (stripboard) and tagboard guitar and bass effect layouts that we have put together covering many classic and popular effects in growing numbers. Many of these have been posted on freestompboxes.org, so check that site out for great discussions on building your own effect pedals. Enjoy the builds and please also visit us on Facebook and Twitter
So I randomly stumbled across the schematic for this one over at FSB and as always thought it would be a nice addition. Just like any other Way Huge pedal I think it sounds badass.
From the Source:
The mighty Angry Troll Linear Boost Amplifier from Way Huge
Electronics serves up generous portions of volume and gain to pummel the
input of your amp with up to +50dB of gain. It adds bite and punch
while transforming your mild mannered tone into a beastly sonic
onslaught! The Angry Troll's two controls interact like a vintage mic
pre amp. The Anger knob-a rotary switch with six Fists of Fury
positions-adjusts the amount of gain created by the Troll's op-amp,
while the Volume knob regulates the overall output level. High grade
components are used for a precisely tuned circuit that works like an
extension of your amp. Another tone monster from the mind of Mr. Huge!
Layout 1: Stock Normal Layout
Layout 2: Was kinda requested below. Modded to remove the fist switch, which controls the gain, and replace it with a pot. Quick note about this is that the way the switch is wired when it's at position 1 it has the most resistance allowing a clean tone. according to my calculations at Sw1 there should be 62.5k resistance, and since there's no 62.5k pot you could use a 100k or 50k pot. Nice thing about doing this is the board shrunk, all pot wires are connected to the board, will give more options for grit, and it should be a stupid simple build.
Great find! The rotary just adds between 1.5 and 60k between pin 6 and ground, right? Then it could be replaced with e.g. a 100k pot wired as variable resitor (maybe with 160k in parallel to make it approx. 60k) as a simple mod - am I thinking correctly? Cheers!
here only 3 not electrolitic cap on board. it's 330pf, 100nf and... it has mark "1.0J63" on it so i think that its 1uf. So it must be 330pf (monolithic ceramic) and 100nf (marked as 104) red film cap.
Call this verified! I used a 47p instead of the 330p as i have only just noticed the change as i was building. Still sounds pretty awesome with a 47p. Will remove and socket to see what it changes. Thanks for the layout Zach!
The pot version is in error. The 100n cap connects to ground, but the other lead is floating. Plus the gain pot's lug 1 cannot be connected to ground. Refer to OD250/Dist+ to see hot to wire the gain pot. Only two terminals are used. +m
crap, when you're right you're right. i wasn't thinking and was on autopilot when i was switching the switch to a pot. i fixed the layout, and tied lugs 2&1 together similar to the MXR Dist+
Looks better. However, there should be 1K5 resistor between gain pot and 100n cap to get the pot settings per original. Also, the C-taper is a must with this gain control method.
I was thinking antilog would be best too, but wasn't sure. With changing the switch to a pot I think with it as is you'll get more distortion with the pot due to being able to get lower resistance then 1.5k. Really to make the pot have similar range to the switch, not only would there need to be the 1.5k resistor, but a 160k resistor across the pot lugs to bring it down to 61.5k. I could be wrong though.
Miro is right, you would need a 1k5 resistor between the 100nF cap and the Gain1&2 connection to work as the original. That sets the minimum gain to about 310. As per the current layout there is no minimum resistance, so I think the maximum gain would be theoretically infinite causing oscillation at the maximum setting of the gain pot.
Putting a 160k resistor across the lugs would not only change the value of the pot but also would alter the taper, making it behave more like a linear pot. In this case that wouldn't be good as the big changes in the gain would shift towards the end of the turn of the pot. I'd rather suggest either a C100k or a C50k. With the former one would get less gain at the minimum setting and to have the whole range shifted a bit to the clockwise direction of the turn of the pot, and with the latter the distribution of the gain settings would be more even across the whole turn, but the minimum gain would be more than in the one with the gain switch. I personally would probably go with the C50k pot.
As Csaba said, without the 1K5, we'll run into oscillation issues unless the feedback loops small cap is upped considerably - this'll result in unwanted loss of high frequencies. The C100K will only add more of the lower gain settings and due to C taper, the sweep would still work very well, without notable unusable area. Dist+/OD250 has a C500K pot in similar setup and that works quite well for the whole turn. A trimmer of 5K value to set the maximum gain (in place of 1K5) would also be a quite nice thing to try.
The C50K will work just as well. With only minor loss in lower settings.
Nice circuit anyway. Basically a buffered Dist+/OD250 gain stage without clipping diodes. Lots to tweak in there.
This, also means that there is a reason for 833. Those'll clip more gracefully than some others. Any dual should be tried to see which performs the best.. +
I wait the verify the second version with pot, Im going to buld that with a 4558, think it could work, also, I have 20 4558 an non 833, do that in a Crunch Box and work very well.
I want the Ring worm :P someone needs to hook that up.. I heard it has carrier frequency oscillation real bad even when not playing though. I guess for some things you just have to make due ;)
Also would increasing the input cap add in a little more low end? I find it a little too trebly with more anger dialed in Sorry, deleted my previous comment to subscribe.
Thanks Miro. I put a 100nf and 330nf caps on the outside lugs of a three position DPDT switch with a 100nf in the center and it worked great. I'm using it to push an Orange OR15 and it became very trebly with more anger. It was very harsh with my Vox AC10 too. I haven't tried it through the Vox yet but I built it more with the OR15 in mind.
I tried the potentiometer version. I doublechecked everything and the issue is that get very loud noise and beep only at full gain and volume. The guitarsignal shines slightly through heavily distorted. I took 47u instead of 100u and put a 100r instead of 10r. thanks for the Layouts here and keep up the good work!
Hey Zack, great one! Would you mind posting the schematics you used as well?
ReplyDeleteThanks a lot and keep it up.
Cheers.
Jorge
Great find! The rotary just adds between 1.5 and 60k between pin 6 and ground, right? Then it could be replaced with e.g. a 100k pot wired as variable resitor (maybe with 160k in parallel to make it approx. 60k) as a simple mod - am I thinking correctly? Cheers!
ReplyDeletetook care of it for you.
DeleteYeah - thanks! Another one on the build list ;-)
DeleteBetween pin 6 and the 47n of course...
ReplyDeleteHi Jorge,
ReplyDeleteSchematics do not get posted on this site but as it says in the description FSB will have it so head over there mate.
Phil.
Thanks for the tip Phil.
Deletei have one here and can check correct values of caps :)
ReplyDeletehere only 3 not electrolitic cap on board. it's 330pf, 100nf and... it has mark "1.0J63" on it so i think that its 1uf. So it must be 330pf (monolithic ceramic) and 100nf (marked as 104) red film cap.
DeleteAwesome thanks man. I'll make the change to the board.
DeleteThis comment has been removed by the author.
ReplyDeleteCall this verified! I used a 47p instead of the 330p as i have only just noticed the change as i was building. Still sounds pretty awesome with a 47p. Will remove and socket to see what it changes. Thanks for the layout Zach!
ReplyDeleteawesome. can't wait to hear the sound comparison when the caps are switched. always had a soft spot for this one when it came out.
DeleteThe pot version is in error. The 100n cap connects to ground, but the other lead is floating. Plus the gain pot's lug 1 cannot be connected to ground. Refer to OD250/Dist+ to see hot to wire the gain pot. Only two terminals are used.
ReplyDelete+m
crap, when you're right you're right. i wasn't thinking and was on autopilot when i was switching the switch to a pot. i fixed the layout, and tied lugs 2&1 together similar to the MXR Dist+
DeleteLooks better. However, there should be 1K5 resistor between gain pot and 100n cap to get the pot settings per original. Also, the C-taper is a must with this gain control method.
DeleteI might build one myself soon...
+m
I was thinking antilog would be best too, but wasn't sure. With changing the switch to a pot I think with it as is you'll get more distortion with the pot due to being able to get lower resistance then 1.5k. Really to make the pot have similar range to the switch, not only would there need to be the 1.5k resistor, but a 160k resistor across the pot lugs to bring it down to 61.5k. I could be wrong though.
DeleteMiro is right, you would need a 1k5 resistor between the 100nF cap and the Gain1&2 connection to work as the original. That sets the minimum gain to about 310. As per the current layout there is no minimum resistance, so I think the maximum gain would be theoretically infinite causing oscillation at the maximum setting of the gain pot.
DeletePutting a 160k resistor across the lugs would not only change the value of the pot but also would alter the taper, making it behave more like a linear pot. In this case that wouldn't be good as the big changes in the gain would shift towards the end of the turn of the pot. I'd rather suggest either a C100k or a C50k. With the former one would get less gain at the minimum setting and to have the whole range shifted a bit to the clockwise direction of the turn of the pot, and with the latter the distribution of the gain settings would be more even across the whole turn, but the minimum gain would be more than in the one with the gain switch. I personally would probably go with the C50k pot.
As Csaba said, without the 1K5, we'll run into oscillation issues unless the feedback loops small cap is upped considerably - this'll result in unwanted loss of high frequencies. The C100K will only add more of the lower gain settings and due to C taper, the sweep would still work very well, without notable unusable area. Dist+/OD250 has a C500K pot in similar setup and that works quite well for the whole turn. A trimmer of 5K value to set the maximum gain (in place of 1K5) would also be a quite nice thing to try.
DeleteThe C50K will work just as well. With only minor loss in lower settings.
Nice circuit anyway. Basically a buffered Dist+/OD250 gain stage without clipping diodes. Lots to tweak in there.
This, also means that there is a reason for 833. Those'll clip more gracefully than some others. Any dual should be tried to see which performs the best..
+
Ah. Did not even think that oscilatoin could be an issue. Simple change and I'll fix it when I get back from class.
DeleteI wait the verify the second version with pot, Im going to buld that with a 4558, think it could work, also, I have 20 4558 an non 833, do that in a Crunch Box and work very well.
ReplyDeleteCan't wait to try this one out! More Way Huge layouts please!
ReplyDeletedon't worry. i've got a few waiting in the wings.
DeleteI want the Ring worm :P someone needs to hook that up.. I heard it has carrier frequency oscillation real bad even when not playing though. I guess for some things you just have to make due ;)
DeleteCan we have the Way Huge Ring Worm PLEASE!
ReplyDeleteVersion with the anger pot works great. Thanks Zach.
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteAlso would increasing the input cap add in a little more low end? I find it a little too trebly with more anger dialed in Sorry, deleted my previous comment to subscribe.
ReplyDeleteNope. The 1u is not cutting your lows. Up the 100n for 220n. That'll take the high pass filter rolloff frequency created by gain amp way lower.
Delete+m
Thanks Miro. I put a 100nf and 330nf caps on the outside lugs of a three position DPDT switch with a 100nf in the center and it worked great. I'm using it to push an Orange OR15 and it became very trebly with more anger. It was very harsh with my Vox AC10 too. I haven't tried it through the Vox yet but I built it more with the OR15 in mind.
ReplyDeleteUgh, I only have two 100uf caps left... Can any of them be swapped for a lower value? Have a bunch of 33's and 47's, but nothing higher at the moment.
ReplyDeleteJust use 47u caps, it will work fine
ReplyDeleteI tried the potentiometer version. I doublechecked everything and the issue is that get very loud noise and beep only at full gain and volume. The guitarsignal shines slightly through heavily distorted. I took 47u instead of 100u and put a 100r instead of 10r. thanks for the Layouts here and keep up the good work!
ReplyDelete