Info about Marc's original:
A faithful recreation of that old-school big box that gave us our start
Creamy, sustaining, amp-blowing-up, huge distortion with a grainy, ear-pleasing, low-fi edge and just the right amount of 'hair'
Heavy does not have to mean harsh or unnatural or even modern
Finally a tone control that is actually useful and powerful, yet does not sound bad at any setting
Makes a single-coil pickup sound more like a humbucker, yet doesn't completely obliterate the guitar's tone
Makes a clean amp sound like a dirty, cranked amp, even at low volume--preamp or power-tube distortion not required.
The tone of these transistors is nearly identical to the NOS units the original Mayonaise used (they look the same, too). Just a couple of minor capacitor tweaks take it the rest of the way there. Made of the same types of parts as used in our first product ever, which was a sonic clone of the circa 1971 "triangle knob" version fuzz box that used the legendary and unobtainable FS36999 transistors.
Has all that original pillowiness, grit, compression, and near infinite sustain as the original.
You left the SW1 wire in the layout :)
ReplyDeleteBugger :o)
Deletelol you guys are to funny sometimes
Deletewhat other transistors can we use?i cant find data on SE4021
ReplyDeleteAnything NPN silicon. 2N5088, 2N5089, BC550C, MPSA18 etc etc
DeleteYou can get the SE4021 from smallbear. Not cheap at $2.25 a pop, but I think I may buy them for this build. Skreddy knows what's good
ReplyDeleteyep. I just ordered some from smallbear.
DeleteSame here! Was putting in a smallbear order for a madbean harbinger1 for some stuff and saw this post so added a set of SE4021's in the mix for this one...
DeleteThanks for the great layout!
There was a small correction to the schematic, Q3 collector resistor should be 18K, now corrected.
ReplyDeleteYou can verify this one! It sounds awesome! I used se4021's for the transistors. And all ceramics except for the 220n's and 4n7. Thanks for another great layout!
ReplyDeleteExcellent, thanks for verifying buddy
DeleteWill this layout fit those 1/2w CC resistors? Was reading that could be some added mojo to this one! hehee
ReplyDeleteNot unless you have some of them standing. 1/4W should be ok though
DeleteI used to have a Skreddy Supa Tone. Resistors were all carbon comp, though they looked more like 1/4w than 1/2w
ReplyDeleteCaps were a mix of greenies, Panasonic ecq-v, orange drop, and ceramic disc
It sounded so good. I had to sell it to pay for my car getting impounded.. That's one pedal I really want back. It was so crunchy and crushing sounding
I just built the board and now just have to wire it up for testing. I used all carbon comp resistors, multi-layer ceramic caps and NOS SE4021 transistors, so hopefully, it should be a pretty good clone of the original Mayo III.
ReplyDeletepic of the board:
http://johnkvintageguitars.homestead.com/Effects/Fuzz-ODs/Skreddy/Skreddy_MayoIII-board.jpg
I just tested it and it sounds great. I actually prefer the taper of the gain pot to be a log since with the stock linear it almost all comes on at once.
DeleteGreat looking build mate. I don't care whether people buy into the mojo or not, but builds using carbon comp resistors always look the dogs bollocks! And I've never had any excess noise when I've used them and the results have always sounded excellent to me.
Deletethanks Mark. and I agree, I think that the carbon comps look cool. i'm not sure that I buy into the 'mojo' of them, but this build does sound incredible, so maybe they do have something to do with it. ;-)
Deletehere she is completed:
http://johnkvintageguitars.homestead.com/Effects/Fuzz-ODs/Skreddy/MayoIII-01.jpg
http://johnkvintageguitars.homestead.com/Effects/Fuzz-ODs/Skreddy/MayoIII-02.jpg
That looks beautiful, John! If you wouldn't mind me asking, where did you get the carbon comps?
DeleteOnly place I've really found with a good selection is mouser, but I don't understand how to use their website
thanks. and yep, I got the carbon comps at mouser.
DeleteHi
ReplyDeleteI'm a total electronics newbie, but a longtime guitarplayer. And I have been bitten by the fuzz bug.
I got my hands on some se4021 but I'm having trouble getting the D5 BAT47.
Is there an alternative? (BAT46?), and how does D5 affect sound?
Thanks
I doesn't affect the sound at all, it's just a reverse polarity protection diode. Try a 1N5817, 1N5818, BAT41, BAT42, BAT85, 1N60P or any other schottky diode you can find. They all have a very similar forward voltage drop and so will have essentially identical results.
DeleteThanks Mark
DeleteSo I guess a good choice for this build would be cc resistors. What about caps.
Should it be tantalum's?
Marc tends to use ceramics for the vast majority of the caps. In my Pink Flesh they are mostly the big round ceramics with a few polyesters which I think is the input cap, the two caps at Tone 1 and 3, and maybe the caps in series with the back to back diode pair at Q2 and 3. The larger filter cap is a standard electrolytic.
DeleteHi again
DeleteThe big round ceramics.... like this?
http://www.musikding.de/Ceramic-Disc-10pF-1kV
And the polyesters...
http://www.musikding.de/PS-01uF-400V_1
or can you point me in the right direction?
As I said. I'm a total newbie ;o)
Any ceramics or polyesters will work fine so yes
DeleteIs it really worth it to use CC resistors?
ReplyDeleteIt depends what your expectations are :o) I like CC builds because they look so cool, and everything I've built with them sounded awesome. But then they would almost certainly also sound awesome if I'd built them with metal film. I think sometimes the tolerance and drift of CCs can get you in a sweet spot of resistance values sometimes, but then the opposite could equally be true and the tight tolerances of metal film could get you in a sweet spot in certain builds.
DeleteI think it's nice to have both types and just give things like this a try but whether or not they are worth it is in the eye of the beholder holding the wallet. :o)
Anyone notice the circuit doesn't have lots of volume output? I built mine with a BAT41 and SE4021s from Small Bear. Circuit works and sounds good, but there isn't as much output as I was expecting. Anyone else notice this?
ReplyDeleteHi
ReplyDeleteI built this with SE4021 from smallbear and 0,5w cc resistors. Yes, it's really crowded....
The distortion in this box is really great!!.
But the tone knob in my build doesn't do much. I compared the layout to my build several times, but I cant see any mistakes. Fully ccw it has a little more treble, but its barely noticeable.
Any ideas to what I've done wrong?
Double check that you used the right value for the tone pot and test it so you can rule out whether or not it's defective
ReplyDeleteIf that's not it then look carefully at your wiring, any misplaced, missing, or incorrect components, solder bridges, etc
Finally got around to it.
DeleteChecked the pot, and it's ok. Checked the layout again and again. But cant find any errors.
It sounds great but there's no tone control. When listening to the background noise only, and turning tone fully ccw, I can here a little more high end.
Any suggestions to what parts I should start replacing?
Your tone pot may have a damaged track. The tone pot is a fairly simple arrangement, check the soldering and values of the resistor and cap connected on the Tone 1 and Tone 3 rows. Knife between all the gaps, because if it isn't working you either have a problem with a part, or a physical error with your build, through maybe a cold joint, unwanted bridge or something similar.
DeleteHad some weird problems with this build, as I soldered the negative lead of the 100uf cap wrong, but now it works, including with SE4021's. Sounds great even on my little practice amp. I used a 1N4001 though instead of the BAT47. Don't have any of those, but I could always install a 1N5817 if need be. Then again, should I?
ReplyDeleteChanged the pot, didn't help.
ReplyDeleteI desoldered the caps at tone 3. Couldn't find any errors, soldered them back, and now it works!
I will redo this build though. With the caps I used and the 0,5 w resistors, its a very tight build.
But it does sound amazing!
Just one question....
ReplyDeleteI built this with caps that were way to big. I looked at the photo of John's build and was wondering what type of caps they are.
Are they like these?
http://www.taydaelectronics.com/capacitors/monolithic-ceramic-capacitor/0-01uf-50v-multilayer-monolithic-ceramic-capacitor.html
Thanks.
Niels
I have a problem with the tone stack. Volume snd gain works as expected but tone adds bass (or cuts trebles) counterclockwise as well as it turns up the volume and clockwise it turns down the volume to zero fully clockwise.
ReplyDeleteTheres as well a overall Volume attenuation with the pedal on.
Checked solder bridges with multimeter, values, position,...
Im using 2 mpsa18 and other 2 trannies refurbished from an old music device (checked it with atlas tester, both workin BJT NPN hfe~400). I'v tried others as well, 2n3904,... (I hace no high gain right here.)
Some caps are refurbished too the phillips red/orante ones and the multilayer ceramic blue. Could it be the problem?
Here is a photo: http://imgur.com/yfeqPqh
Tope you can help me.. Cheers ;)
Damn autocorrect....
DeleteSolved, a solder bridge '-.- in multimeter we trust. And in double check... Or triple
DeleteThis comment has been removed by the author.
ReplyDelete