Sunday 24 September 2017

BJFE Sparkling Yellow Overdrive V2

Not much info on this. From what I've read from the BJFE forum is that the 3 knob Sparkling Yellow Overdrive was a short BJFE Customshop run that's supposed to have that old school early American tones, think Fender Tweed, Blonde, and Brownface.

Video of the 3 Knob


Video of Bearfoot version of the 4 Knob (Closest Video I could find)



Original 3 Knob Limited Run



4 Knob Production Version With M Knob



Posted by at 06:25
Tags: , , ,

16 comments:

  1. HamishR24 September 2017 at 12:47

    Well it works! I had to swap the distortion leads from 2 and 3 to one and two, but otherwise it all seems good. I guessed and used a 2N5457 - it works.

    I might try to make the tone control more effective - it's a bright pedal and the tone doesn't do a lot. Also needs a bit more low end. There is a lot of gain on tap here. So a few simple mods and it could be a great OD.

    Thanks for the layout!

    ReplyDelete
    Replies
    1. Zach24 September 2017 at 15:36

      cheers man. can't believe i forgot to put in the FET in the notes. you were right that it's a 2N5457. i made the changes to the layout, and added the note for the transistor.

      it makes sense that this is a bright pedal since the amps it's supposed to be reminiscent of are all bright sounding amps. take a look at the dyna red distortion and mods done to it. this is the same topography, just has some different values.

      Delete
    2. HamishR24 September 2017 at 16:08

      Yeah I can see the similarity. I wish someone would work out the schematic to the Strawberry overdrive that Bjorn designed for One Control - I suspect it's not far from this.

      I'm looking forward to building the 4-knob Sparkling Yellow. I think it will be a better pedal than this one, but I just like building 'em. :-)

      Delete
    3. Zach24 September 2017 at 16:12

      haven't seen a schematic for it. if i do i'll gladly take a look at it. side note, i'm pretty sure that the distortion control should be like it is in the dyna red distortion, so i just made the change and updated the layout.

      Delete
    4. Unknown24 September 2017 at 18:55

      This comment has been removed by the author.

      Delete
  2. Unknown24 September 2017 at 19:09

    Hello! Best regards from Chile! Do you have a schematic for this? Thanks!

    ReplyDelete
    Replies
    1. Zach26 September 2017 at 04:31

      we do not post schematics, and tbh i've had it sitting in my folder for layouts to be created for a long time now so i don't even remember where and when i found it. i would check the usual sources like DIYSB and FSB.

      Delete
  3. HamishR25 September 2017 at 08:41

    Hey Zach - the 4-knob version works a treat! The M knob is a lot like a "nature" knob on other BJFs. CW it gets thinner, CCW it gets thicker and bassier. I big improvement over the 3-knob version.

    But still the treble pot doesn't do very much. Yes at zero it muffles the signal a bit but really it's not very effective. And I wonder how I could increase the mids a bit more?

    Cheers mate! Good stuff!

    ReplyDelete
    Replies
    1. Zach26 September 2017 at 04:37

      great man, that's exactly what it is, seems like bearfoot calls it "M" knob while BJFE calls it "Nature". honestly, it's exactly the same treble setup, cap & pot value, as the dyna red distortion. i haven't built either so i can't say for sure how much it changes the amount of treble. you can try to change the 47nF cap that attaches to treble 2and see how it affects the control.

      Delete
    2. HamishR5 December 2018 at 15:30

      I just revisited this pedal and built myself another. After reading what I wrote I realise that it might have sounded like I was doubting your work - that's not what I meant at all! I am not surprised that the treble pot does so little because I have owned some BJF designed pedals where it is a mystery to me what a knob is supposed to do! Sometimes they do very little indeed.

      I think I'll start by swapping the pot to an audio taper because all the action is in the first 1/10th of the turn.

      Delete
  4. Unknown3 October 2017 at 14:35

    Hi,
    The only schematic I have found is at FSB, and two things are bugging me:
    - the schematic does not include the pair of diodes to ground, after the 1uF cap,
    - and the 3k resistor connected to the 1uF cap to ground, in the bottom left corner, should be connected, at its other end, to pin 2 of the IC, just like the 1K resistor into the 220nF cap to ground; the other 3K resistor should only lead to Distortion 1
    Incidentally, I have just spotted that the 4 knob version is 22 columns wide, not 21 as shown in the layout, but that's not a major point. ^^
    Have I got the wrong schematic, or does the layout need to be amended?

    ReplyDelete
    Replies
    1. Zach4 October 2017 at 03:14

      good catches. the schematic i have is similar to that one. i used another similar bjfe pedal as a template when making it and didn't realize i needed to remove those extra diodes. fixed both layouts. cheers man.

      Delete
    2. Unknown4 October 2017 at 09:07

      Not at all: thank YOU, Zach, for the effort you put in those layouts! :)

      Delete
  5. HamishR6 December 2018 at 05:55

    Well what do you know? Replacing the Treble pot with an audio taper made enough difference as to make it useful. Really recommend an A50K for Treble.

    ReplyDelete
  6. Mr.Baiser26 September 2019 at 23:33

    Is there a schematic that can really be regarded as verified? Especially of version 1?

    ReplyDelete
  7. Damian8 November 2021 at 16:12

    May i use CA3130 instead 3130EZ ?

    ReplyDelete

Subscribe to: Post Comments (Atom)