And I didn't expect it but this will fit in a 1590B too (doh!) so the Lite version may not get built quite as often now. But still a good exercise in adapting these things and I'm glad there is a more compact version available if someone wants to use it.
This one has also been verified by our resident Finnish metal head who sent me a comparison clip against an original and it sounds identical to me, so you're good to go on the build! Thanks again to Miro, the building machine! :o)
Here's the clip, so you can guess which is which
Info about the original:
The HM-2 is a distortion effect specially designed for Heavy Metal music. In spite of its compact body, it features an extremely wide dynamic range, therefore allowing rich, dynamic distortion sounds. Also, the HM-2 can be effectively used even with a single coil pickup guitar lo low output level, because of its high gain. Wide variety of tone color creation is made possible with two Color Mix Controls.
Why aye bonnie lad, blondegraemey's demo:
And after the discussion below, a modded version with additional mids pot.
The original is the first one, and the clone, the second. Am I wrong? :P
ReplyDeleteThey sound quite similar, but there's a slight difference between, as the first sounds rouder to my ears.
Love this pedal, and even thougt I have an original Boss HM-2 will surely build this board just for the sheer pleasure of building this great effect!
Didn't want to reveal it so quickly :) You are correct. My circuit is only connected to a test box, so that could also make a difference. I think i'm going to box it up tomorrow. My bench recording equipment is crap, so the clip is not too hi-fi due to that.
DeleteEither way, the differences in sound are very, very small, considering that all the semiconductors are different from the original (and i used 2µ2 cap instead of 1µ5). Since the semiconductors i used for the Lite version worked so well, i used the same ones for this - 3x LM358 for dual opamps, BF245A, C3198 and A733 for transistors. None of those are exact equivalent to the ones used on the original (except for the JFET). I think this is the best circuit for those LM358s due to their (otherwise annoying) tendency of adding brutal distortion on their own. That being said - i never got them sounding good in any overdrive design..
This is a great distortion, but the idiotic ACA power supply requirement on the original sucks. And modding is out of the question, 'cause i want to keep its value. So building a clone is a lot better option than paying 120€/£100/$160 for a used unit. Especially now that Mark did the impossible and squeezed the circuit in 20x26. 1590B is smaller than standard Boss enclosure...
Of course the original is nice to have, if you can get one for reasonable price. Got mine from london for ~£52 - so obviously i had to buy it.
+m
Yeah, ACA sucks. To tell you the truth, the HM-2 is the only Aca Boss pedal that I have not modified still to use regular +9v adaptor (my DF-2, CS-3 and DS-1 have been modified)
DeleteI think that I have a few LM358 somewhere, so i'll build the board with these ic's.
By the way, I had to do a long research, but I finally purchased my Hm-2 for 40 euros, shippin' included. Have to tell too that I was asked even 175 euros for units of similar age and use, sheer madness for this effect!
By the way, if anyone's interested, Spain is a cool place to buy this effect, and similar ones, like the HM-3 or the MT-2, as many "guitar gurus" in my country tell that these effects really suck, so to be cool in forums and websites, you have to say that "Boss HM-MT are pure crap" and the second hand market is really interesting for these Boss effects, being 60 euros an usual price.
DeleteSame with some other pedals and amps. My Valvestate 8100 head was just 100 euros! :P
I do think MT-2 sucks :) I have two of those and i'm currently trying to sell the other for 40€, but no luck yet. Had to get new EQ pots for it, so i'm not letting it go for anything less.
DeleteBeen planning on getting HM-3 and ML-2 for myself, but i have not come across good deals on them so far. Anyone want to trade MT-2 for HM-3 or ML-2? :)
Got myself a '85 DF-2 recently. The guy who i bought it from thought it was broken due to ACA supply requirement.
MD-2 is great by the way... especially when paired with a chorus. DS-2 isn't bad either.
I'm not a fan of Boss pedals, but those seem to be accumulating on my collection - http://mirosol.kapsi.fi/collection/boss/
But back to the subject...
HM-2 has unique, strong middle with massive lows and even the highs are clipped in a lot neater manner than on most metal distortions. I think it is unique, as i don't currently know of any other circuit with similar, dual high Q filters. Nor anything that sounds even remotely the same. Makes me wonder why Boss didn't continue producing it. Even after the swedes made it a cult classic in late 90's.
+m
I have a Boss MZ-2 Metalizer... I still love this pedal although I rarely use it other than in the studio. The built in doubler and chorus was handy at times. These were made in Japan and only for a short time.
DeleteI read somewhere that in the tonestack, the high knob also controls the mids. The relevant mids circuitry is tied to the highs. Any idea how to detach the mids into a separate mids control?
ReplyDelete...by creating a third active gyrator filter for mids and changing the high Q point of the original high gyrator.
DeleteSo no. I don't think it can be done in any easy, simple way.
+m
I just found the schematic. There are three active opamps used for the Q. Two are linked to HIGH and it might be that one of these deals with mids and the other highs. The remaining opamp is linked to LOW so that is obvious.
DeleteI do not know if one of the opamp controls the mids. I am guessing here. If we separate the 0.1uF output and 0.15uF outputs, linking one of these outputs to lug 2 of a new B10k pot with lug 1 going to + of the volume recovery opamp and lug 3 going to - of the same opamp (wired like the existing knobs) might give us a MID control.
Again, I am guessing here. On lvlark's layout, if we move the bottom leg of the 100n cap moved up 3 rows to just above Low 2. This 100n might control highs so I am moving the HIGH 2 wire to this new row. The old HIGH 2 becomes MID 2 in a new B10k pot. MID 1 is connected to HIGH 1 & LOW 1. MID 3 is connected to HIGH 3 & LOW 3.
Again, all purely guesswork...
Can someone educate me on how a gyrator filter works? Thanks!
Gyrators are covered on this article:
Deletehttp://www.geofex.com/Article_Folders/EQs/paramet.htm
I have no idea if that will work...
+m
Yes that makes sense to me, and working out the frequencies it seems that the 150n cap will go to the Mids 2 lug. Check out this Excel file which is from the spreadsheet I keep all of my parts logged.
Deletehttp://www.filedropper.com/calcs
There are a few calculators that I use in there which others may find useful and one for gyrators
Although there is some slight difference, the footswitch click gave away which was which... :)
DeleteWow Mark, this is the best HM-2 vero out there. Well done!
ReplyDeleteI just got an extra tall board from MKLEC that would suit this perfectly
This is very, very cool. Thank you so very much! I will build this very soon and compare them to my '84 MIJ and' 89 MIT, which does have a very minute difference in their sound. Tbh I also ordered the Behringer HM300, and might as well make one huge 'scientific' comparison.
ReplyDeleteThis is very, very cool. Thank you so very much! I will build this very soon and compare them to my '84 MIJ and' 89 MIT, which does have a very minute difference in their sound. Tbh I also ordered the Behringer HM300, and might as well make one huge 'scientific' comparison.
ReplyDeleteOh, hehe. I just watched the video, and he says that the sound on MIT and MIJ are the same... well, not quite ;) the nature of the tone sure is similar, but the mid bump on the MIT is 'sharper' kinda, anyways, if one listens closely, the difference is clear. As stated above, i'm gonna make a thorough comparison with frequency analysis and maybe som oscilloscope shots and what not.
ReplyDeleteThe thing is, with this and a lot of similar pedals, you could almost certainly find exactly the same differences between two MIJ pedals. The frequency response from the gyrator could shift noticeably if maybe a cap with a 10% tolerance was used and one was at the upper and the other at the lower end of the tolerance scale. These are the figures based on the 150n cap:
DeleteLower tolerance 135n - 915Hz
Upper tolerance 165n - 828Hz
So an almost 100hz difference in the mid point frequency response using exactly the same cap. If the cap had a 20% tolerance the difference could be as much as 180hz.
I think the important thing here is that if you want to fine tune the frequency response to get slightly more or less lows, mids or highs, then it's pretty easy to do no matter which version of the pedal you have. Just change a cap or two.
Hi Mark,
DeleteThank you for your answer. And yes, your statement seem very likely to be the case in point here :) Never thought of the tolerance being high enough to affect the tone in such a pronounced manner. It is surely worth experimenting with.
I just had another look at it and think swapping the three 330R resistors with multi-turn trimmers would be great for tweaking the frequency response. If you use 500 ohm multi-turns preset at the 330 ohm value of the resistor and then tweak from there. Set to 500 ohm (using the mids gyrator as an example) the frequency would be set to 705hz, set to around 250 ohms it would be around 1khz. So I think that would be a really precise way of setting this up exactly how you want it in all 3 bands.
Delete5 pot version added with additional mids pot.
ReplyDeleteThanks for following through on my Mids question! Much appreciated. That 330 ohm resistor seems to make a significant difference. I might have to use your (very useful) calculators to work out the EQ ranges.
DeleteHow does this pedal compare to a metal zone MT 2?
ReplyDeleteThey are nothing alike. :) Controls are completely different and the clipping textures are from different planets.
DeletePersonally i think MT-2 wouldn't be worth drawing a layout, nor building it. There are six pots and the circuit is even bigger than this, so it would be real pain to squeeze in 1590B. Plus cost of the parts would be more than a used unit. One just went for 29€ on ebay.
You can buy one use MT-2 off from me if you want to :)
+m
Thanks, but I have an MT-2! :-p
DeleteThat's why I was asking, I can get some nice lead tones out of it drowning it in chorus an delays and sending it through a clean solid state amp, I tried to plug it into my freshly built madamp a15 and just cannot find a use for it, even though it has a wicked tone stack, the two kinds of clipping just don't play nice together ... I'm trying to find something that will ...
This comment has been removed by the author.
ReplyDeleteA layout of this with the pinout for the M5216L layout would be great, since I have a bunch of them. since all 8 pins are in a line and it's not a DIP package.
DeleteI know anyone who has the SIP version of the IC would also like this, but I don't think it's going to happen to be honest John. I've done a SIP8 layout before for the Eternity and I can tell from that experience that the layout would essentially need re-doing from scratch apart from the top 8 rows that the transistors are on, which would be awkward and take time in order to accommodate an unusual IC that most people won't use, and isn't necessary to use anyway as the M5216L can also be obtained in a DIP8 package.
DeleteIf you do want to build it with the original inline IC I'd suggest some sort of SIP8 to DIP8 converter, or even make one on a small piece of vero or perf and use this kind of inline connector to mount it in a DIP8 configuration.
http://www.ebay.co.uk/itm/191024596739
Is there any good substitute for the 2SA970?
ReplyDeleteAny silicon PNP with same pinout should be fine. 2SA733 is what i used and it's working well.
Deletehttp://www.taydaelectronics.com/t-transistors/other-transistors/2sa733-transistor-pnp-50v-100ma-nec.html
+m
Ok, i finally got around to do some soundclips :) This is only for the die-hard HM-2 fans thogh, i guess.
ReplyDeletehttp://www.tonetroll.com/2014/05/boss-hm-2-vs-behringer-hm300.html
Now i need to build one, and see how it compares to the other ones in my possession.
Just got this one working. Needed to knife those tracks! You know those really tiny beads of solder that get caught between the tracks and cause a short..
ReplyDeleteThis circuit is awesome as we all already know. I just love this badass layout
Glad you got it going buddy :o)
DeleteHaha thanks. I've been wanting one of these forever so it's great to build one.
DeleteIt has exceeded my expectations. My first impressions are pretty much love at first chugga chugga skree
I've got some Dano pedals that I think are copies of the Metal Zone and this HM-2 is much more clear and natural sounding but still totally mangled and heavy
Hey! I stumbled across your page while looking for info on replacing the H color potentiometer. The H pot on mine is completely broken. I called Boss, and they no longer sell the part. Any info on this part would be greatly appreciated. Thanks!
ReplyDeleteHi just built this. I used TL072 ics, socketed. There was a high pitched whine, sometimes worse. Removing the ones for the tone controls got me back to the plain overdrive sound, with no whine. Replacing those with 4558(?) from tubescreamer spares stopped it! Can some ics be bad, or is there likely some other problem with my build I've just covered up with the new ics? Thanks!
ReplyDeleteI'm disappointed that no-one has mentioned Sunlight Studios or Entombed yet :/
ReplyDeleteThe 2nd hand market for this pedal is INSANE. I just bought a Behringer HM300, which is supposed to be a modern reissue, and for the £19 i shelled out, its one hell of a clone even if it is pink!
At some point however, I would like to put this together and test out the Mids mod.
Oh and please... the HM-2 and MT-2 are NOTHING alike. Basically got to Youtube and listen to the guitar sound on Entombed's Left Hand Path (or any other 90s Swedish death metal for that matter) and find out why this pedal is so sought after by Death Metal guitarists and bass players.
It depends... I had mine for 35 € (second hand) :P, just time and patience.
DeleteJ.
Hi there, congratulations for your work!
ReplyDeleteI have an old HM-2, and want to try de Mid Pot. Is there also some way to add another pot for tweak de Mid Freq, like the concentric pot in the MT-2? Would it be in the place of the 330R resistor linked to the 150n that goes to the Mid 2? If it's possible, what would be the value? Thank you very much.
Does it say somewhere that I missed what kind of transistors I need? I assume 2 different types. I've got a handful of transistors but I don't know what I'm looking for or like what ranges/style/etc.
ReplyDeleteSee where it says Q1, Q2 and Q3? Those are the transistor model numbers. There will likely be equivalents you can use instead, so check through the thread above and maybe Google ' HM2 transistors' or something.
DeleteThis comment has been removed by the author.
ReplyDeleteMeasure all the transistor and IC pin voltages and post the results. That will give us the best clue if something looks amiss.
DeleteThis comment has been removed by the author.
DeleteThis comment has been removed by the author.
DeleteThis comment has been removed by the author.
Deletehey! i dont know if its possible, but i want to make this pedal without not pots, because i only want to use it with all pots at max. is it possible with this layout somehow?
ReplyDeletedist is a 250k pot.
Deletetake a 250k resistor, and solder it between dist1 and dist3 wires.then connect dist2 to dist3, and now you have dist maxed out for ever!do the same thing with the other pots and you're good to go.
thanks, i will start it soon
DeleteHi,
ReplyDeletemaybe I am doing something wrong but I hear loud radio static when turning mids knob...can someone detect where is problem? also lows and highs don't make to much of difference in tone when used...what can be wrong? Distortion is present and volume pot is ok.
Anyone? Please...
DeleteI built this a while back and it sounds great but I would really like to add some clipping options to it I am just not sure which diodes to swap out. anybody have any experience or ideas which diodes i should pull? I appreciate any feedback thanks guys
ReplyDeleteThis looks awesome! I've read that it fits inside a 1590B enclosure, but would it fit inside an original Boss HM-2 case? I was lucky enough to have somebody send me the case and the original pots, but would it be possible to put this vero build in the boss case? Cheers guys :)
ReplyDeleteShould fit, yes, but you'll need to figure out what to do with the bypass switching. This layout is intented for true bypass and 2PDT/#PDT stomp...
Delete+m
This comment has been removed by the author.
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteHi guys, I want to build this pedal, but I see that this layout ask for 100K pots for L and H color knobs and according to a schematic that I saw they should be 10K linear pots. Is that correct?
ReplyDeleteI've just checked it and I think you're right, God knows how that one got through the net when I did it so long ago and when quite a few people have built it. I assume the frequency response must still be usable. I'll end it and update, thanks for the heads up.
DeleteBuilt this using the now outdated layout with 100K lin pots for L and H colour, I'll swap them out when 10K pots arrive. Sounds really good anyhow, I used BF245c, 2SC2240, 2SA733 and TL072 ic's. I had a handful of M5216L SIP ic's and so I built a daughterboard to interface them to this layout using the associated datasheets as reference for pinout. Unfortunately it was obvious something was not right, it sounded like a quiet crackly mess! Maybe they were fake M5216L chips, not sure what happenned. TL072's sounded great so I'll stick them back in. Thanks for the layout!
ReplyDeleteI couldn't find a the transistors for Q2 and Q3 (2SC2240, 2SA970). There was a different veroboard layout that used 2N5088 and 2N5087 for those. Would those work or should I look for a different solution? I need a buzzsaw sound in my life.
ReplyDeleteWorks great, possibly the largest build I've done for a distortion. Did mine originally with the 100k pots, but changed them to 10k's after looking at a few schematics. I also changed the 3k3 resistor (left side, by the high and low 1 and 2 connections) to a 12k to bump up the volume. That resistor is also worth experimenting - for instance, if you pull it out, you get a lot of extra volume, but you also lose some of the extreme chainsaw mids.
ReplyDeleteCorrection: *High and Low 1 & 3 connections
DeleteIf I wanted to have a switch for mids rather than a pot, is that possible and if so how would I go about it?
ReplyDeletehas anyone got this one working? All i get is noise when i turn the pot meters but no guitar sound. I built this twice with brand new components and checked all connections but nada :(
ReplyDeleteWhat do you use to make jumpers for 9 or 10 rows long, component lugs are too shorts :/
ReplyDeleteWire
ReplyDelete22AWG solid wire would be good
quick question. what should i do if i wanted to have a knob-less version of this pedal that would behave like if i set all knobs to max? replace the pots with fixed value resistors?
ReplyDeleteJumper the 2+3 wires on each pot and place a resistor with a value of each pot between wires 1+2.
Delete+m
thanks man!
DeleteI'm trying to solely isolate the gain stage on this can anyone help please, i don't need any EQ or volume setting just gain. thanks
ReplyDeleteIt's basically the top row of this schematic after Q4 right to opamp 1a:
Deletehttps://s2.postimg.org/tnggqc2pl/boss-hm2-heavy-metal-schematic.png
The bits up to and including Q4 were all removed because they are part of Boss's switching method which we wouldn't replicate. Everything after opamp 1a is for tone, recovery and volume.
Actually looking at it I did include the first JFET too, so use this scheme:
Deletehttps://s2.postimg.org/h7oca8yqh/boss-hm2-heavy-metal-schematic2.png
Perfect thank you so much!
DeleteJust built this for fun (the mids version). I used 2n5457, 2n5087 and 2n5088 (watch the pinouts) for subs and TL072s at first for the op-amps. this was my first guitar pedal back in the day and I've long long since sold it. I remember it sounded BAD but a lot of that was my ears and amp I think, but it sounded really trashy with a parked wah sound until I changed the op-amps to LM358s and then it really improved things - it actually sounds incredible now, as in way better than it's reputation - so I would recommend them as the go to op-amp in the layout if possible, definitely work very well to my ears!
ReplyDeleteThanks for all the hard work!
I'm fiddling with my own build atm. And the LM358s really improved things a fair bit. But I'm still unsure, if I like it that much.
DeleteDid you end up keeping the subbed transistors? I still have the recommended ones in mine and thinking about trying different ones.
(registered since 2012, had no username yet - damn xD)
DeleteHi IvIark, look like you know your electronics. I'm trying to fix my broken HM-2 with a new distortion pot. I'm haveing tough time finding the new pot as Boss does not make it anymore and the available pots online are too wide. Anyways I wanted to ask you do you know if the distortion pot has to be linear or audio?
ReplyDeleteJust went through the schematic to do some modding and I found an error on this layout compared to the original schem. Namely the 68k resistor on the right of the ICs should go to 9V instead of 4.5V. It can be extended to the row next to the 220uF to get 9V. No idea if this will make a dramatic improvement but I figured it's worth noting.
ReplyDeleteIn any case thanks for the layout!
Thanks for noticing it.
DeleteThis 68k thing is really strange. I read the Boss HM-2 schematic that has, indeed, a 68k from the pin 3 of the upper IC to the 4.5v, and that's ok, and another 68k from the C of Q3 to the 9V, that should be move.
I found two alternative layouts, both verified but with the same mistake.
Here: https://dirtboxlayouts.blogspot.com/2019/06/boss-hm-2-heavy-metal.html
And here:
http://effectslayouts.blogspot.com/2015/10/boss-hm-2-heavy-metal.html
where the mistake it's been reported, but it seems fine, anyway.
Thanks guys I'll go over it when I get chance this weekend and make any required corrections. Cheers
DeleteJust to add my 2 cents on this: check out the build / schematic from Aion FX. That 68k resistor from upper IC's pin 5 to +4,5V should be connected to +9V, according to Aion's schematic. Also, on that schematic Hi, Mid and Low pots are 10kA.
DeleteHello! I had a go at this earlier and cannot seem to get it to work properly. I get sound but hardly any distortion. Volume knob works, low mid and high knobs seem to function as they should. Distortion knob cuts volume when is at 0 but doesn't distort. I'm still new to this (4th pedal) but any help would be greatly appreciated. I've gone through the parts so many times, knifed the tracks, rechecked all my solder. For Q1 I am using 2n5457, Q2 is 5087, and Q3 is 2n5088. ICs are LC358P but have also tried TL072.
ReplyDeleteI measured
Q1
G = 1.93 V
S = 1.31 V
D = 9.05 V
Q2
B = 4.45 V
C= 5.07 V
E= 0.006V
Q3
E= 8.03 V
C = 3.37 V
B = 3.94 V
IC 1 (the most northern one)
1 = 4.43 8 = 9.05
2 = 4.43 7 = 3.37
3 = 4.40 6 = 3.37
4 = 0 5 = 3.36
IC2(in the middle)
1 = 4.44 8 = 9.05
2 = 4.44 7 = 4.43
3 = 4.43 6 = 4.43
4 = 0 5 = 4.39
IC3(the bottom one)
1 = 4.44 8 = 9.05
2 = 4.44 7 = 4.44
3 = 4.39 6 = 4.43
4 = 0 5 = 0
Any help would be greatly appreciated. Thank you very much!
Sorry the formatting of my post got all funky!
DeleteDid you ever figure out what your problem was? I'm getting similar voltages, and same behavior as you described, a little volume, no gain....
DeleteI will try and build a fresh one since I can't find the working HM2 I made a good while back...
DeleteCan I check if you built the standard version or the one with the mids pot?
What ICs/transistors/diodes did you use?
Any deviations from any other components?
Hi there,
ReplyDeleteI built the version with mids control last night, and while I get a class metal sound with my guitar, there is an incredibly annoying high-pitched whine which seems to be related to the 1N34A pair of diodes (I got them from bitsbox so should be okay?).
In my build, I ran cable from where the two diode pairs are to see if I could maybe switch the sound up between different germaniums and silicon diodes. I just have the diodes on a breadboard, and whenever I pull out either one of the wires connecting the 1n34As, the whine stops.
I have tried different diodes, but the whine always kicks in when any germanium diodes are connected. NB: silicon actually reduces the output in place of germanium so unsure if I've done something wrong or if it’s a component issue on the board.
Any help anyone can offer would be amazing. I've made a fair hobby out of building pedals, thanks to all your work on this site, so thanks very much!
Update, the guitar sound is actually a little broken up. Dunno if that helps. Can also post voltages if needs be.
DeleteBuild this one but there is a problem within. Me same as the above post/////gabygab post
ReplyDeleteMine is working now. I think a10k resistor is missing from q3 collector to ground....
ReplyDeleteThe resistor to the right of IC1 is that 10K. It connects to the collector via the top right hand side link.
Deletefind out the mids pot mod layouts high pitch whine problem, [[swap the high pot from 100k to 10k]], whines gone and the proper EQ get, that's it.. op amps: lm358, Q1:bf245 Q2:C945 Q3:A733, 1n60 for D6-7, and thanks Mark again.
ReplyDeleteshort clips here: https://www.youtube.com/watch?v=546LeuYwnE0
I have built three boards at this point and all 3 give the same issue. I followed the build guide exactly all three times. The signal passes perfectly when the pedal is not engaged, but when the pedal is engaged and with all the pots turned all the way up, I get barely any volume and no distortion to the signal.
ReplyDeleteHave any errors been found on the layout, or am I just this unlucky?
Hi there, the layout seems to work for the most part. I got a high pitched whine which was mostly mitigated by changing the 100k 'highs' pot for a 10k. However, the distortion is very heavy and volume should be pretty evident.
ReplyDeleteCould I suggest you post IC and transistor Voltages? This would greatly assist fault-finding.
Do you get any kind of volume at all?
I made the version without the Mids, so it called for 250K Log - Distortion, 10K Log - Volume,
ReplyDelete10K Lin - Low, 10K Lin - High.
IC 1 -
1 - 4.54 / 2 - 4.53 / 3 - 4.38 / 4 - 0 / 5 - 4.02 / 6 - 4.02 / 7 - 4.02 / 8 - 9.14
IC 2 -
1 - 4.54 / 2 - 4.54 / 3 - 4.54 / 4 - 0 / 5 - 4.5 / 6 - 4.54 / 7 - 4.54 / 8 - 9.14
IC 3 -
1 - 4.54 / 2 - 4.54 / 3 - 4.49 / 4 - 0 / 5 - 4.49 / 6 - 4.54 / 7 - 4.54 / 8 - 9.14
Transistors -
Q1 - BF245 - G - 4.13 / S - 0 / D - 9.14
Q2 - 2SC2240 - B - 0.61 / C - 4.22 / E - 0.01
Q3 - 2SA970 - B - 7.65 / C - 4.04 / E - 8.28
With all pots at 10 I can hear the guitar very faintly. It doesn't sound distorted either.
Did you ever get this worked out I have similar voltages, same problem
DeleteI'm going to dig out my build of this and check the transistor voltages. IC voltages look okay based on my limited understanding
DeleteThanks a lot! Any help is appreciated.
DeleteHi Micheal, unfortunately I cannot find my working HM2 build with the mid pot mod. If you can wait a little while longer, I will try and build a fresh one up, assuming I have all the components there.
DeleteCan I just check:
Did you build the standard version, or the one with the mids pot?
What ICs/transistors/diodes have you used?
Any deviations from the components as shown in the layout?
Okay, well the good news is I found the HM2 build that works (apart from a background whine that is only audible when you're not playing). Here are my Voltages but please note, they may not be 'perfect' but somewhere to start for sure:
DeleteSupply - 9.25V
Q1 (BF245A):
G - 4V
S - 4.6V
D - 9V
Q2 (2SC2240):
B - 0.6V
C - 4.6V
E - 0.02V
Q3 (2SA970):
E - 8.2V
C - 3.8V
B - 7.5V
IC1:
1 - 4.4V
2 - 4.4V
3 - 4.4V
4 - 0V
5 - 3.8V
6 - 3.8V
7 - 3.8V
8 - 9V
IC2:
1 - 4.4V
2 - 4.4V
3 - 4.4V
4 - 0V
5 - 4.4V
6 - 4.4V
7 - 4.4V
8 - 9V
IC3:
1 - 4.4V
2 - 4.4V
3 - 4.4V
4 - 0V
5 - 4.5V
6 - 4.5V
7 - 4.5V
8 - 9V
If you post the exact voltages you're getting on here, someone on here may point you in the right direction more quickly
Thanks so much for getting back to me. I'm not home, but I'll get voltages later.
DeleteI built the mid pot version. I'm using TL072s, and I substituted the NPN/PNP pair for a BC549/BC557. I bent the pins around to match the layout, insulated the legs. All other components are as called for.
No worries, happy to help out as I have received good help on here in the past.
DeleteI don't see any issue with the semiconductors you've used, standard NPN and PNP should work as far as I guess. Might look into transistor characteristics if your voltages don't provide insight, but isn't really my ball game.
I'm going to build a fresh one anyway since I just built a splitter/mixer based on one from this site, and thinking I could maybe combine two of these in parallel or something, maybe. But may be Sunday before it's built as I'm working the next three days
Not getting home till late, so no chance for readings today. However , one thing I forgot to mention.
DeleteI found that if I bridge the cut at E6, (essentially bypassing the input buffer) I get a distorted signal. However, it only has normal volume if placed after another buffered effect. I suppose that means the problem is in the buffer section, but I can't figure out where.
No worries, based on that, I would look at the voltages around Q1 and Q2 and ensure Q1 (BF245) is placed in the correct polarity
DeleteHi and many thanks for the layout. I went directly from the upper layout to soldering without breadboard, and it works :-)
ReplyDeleteOnly issue I felt right away is if I dime the Lo pot there is a high pitched shriek sound. Really bad. But if you stay away from the fully CW on the Lo pot, it seems ok. Any ideas as to what could be changed or fixed to mitigate this is very much appreciated.