Here's one for Syd Barrett era Pink Floyd fans. This is the pedal Syd used on tracks like "Interstellar Overdrive". It's more like a buzzy overdrive than a typical fuzz pedal.
I will probably build this with .15" pitch stripboard but you can use .1" pitch as well. The bottom strip is for mounting the board on standoffs but if you're not using standoffs you can cut that row off.
This pedal is normally powered off a pair of AA batteries for the -3V. For daisy chaining you could use the inverter + regulator daughter board that Mark posted with his Maestro FZ-1 layout
Here's the layout with the requested switchable gain boost mod
the requested layout with inverter and regulator onboard. This is unverified
Hey this looks great! Thanks Travis!
ReplyDeleteAny thoughts on transistor HFE and Leakage?
Thanks. I saw a schematic that indicated the hfe was something like
ReplyDeleteQ1: ~80hfe Q2: ~120hfe Q3: ~80 hfe
I would just try starting with anything in that ballpark hfe with moderate leakage and audition different stuff from there
Neat thats pretty much the same as a tonebender. 80 80 120.
DeleteI am having a hard time finding 80hfe or so in my PNP germaniums...
ReplyDeleteCan I use NPN instead? Do I only need to switch the pins to do so?
Flip the transistors (mind the pinout), swap the -9v and +GND, and flip all electro caps.
DeleteI will find another solution then, because I wanted to have 2 PNPs and one NPN...
DeleteI'll try to source some HFE correct PNP Ge...
I would try what you have first and see how it sounds. I've made them with Q1 and Q3 silicone and Q2 Ge. There are some DIYstopboxes threads on it. I've just gotten into measure Ge and all that so i don't know what' ive droped in before, but it seemed forgiving to dropping random stuff in there.
DeleteOn good mod (DIYstompboxes) it to add a 22uf cap to ground on the Q1 emitter in parallel with the 1K resistor, livens it up. good for a switch
I'll post another layout with the switchable cap on Q1 emitter later. Thanks for your input
ReplyDeleteSorry Travis, but I have to mention this again, and just know that: I really appreciate your efforts and contributions, but there is one tiny little detail that is annoying the hell out of me:
ReplyDeleteCOULD YOU PLEASE GIVE YOUR PICTURE-FILES A LOGICAL AND DESCRIPTIVE NAME.
Not automaticly generated names like the one for this picture-file: "62461726-5954-4377-95a9-70e86e7cca2e_zpskux76ki4"
Like most others, I use drag and drop, in order to save the picture files to my laptop (and not the long tedious right-click, save as... and so on...).
I just grab the picture and chuck it in my chosen (offline) Library folder with the rest of the layouts I´ve collected.
And I actually expect to be able to find it easily a couple of days afterwards by name, just by scrolling alphabetically trough the list of files...
But this is not the case with your files, and I easily waste an extra 10 minutes just searching for that damn file, and by the time I find it, my mood as totally changed beacause of that tiny annoyance! NOT GOOD!
In other words: your rutine (or lack of routine) is generating extra (and annoying) activity in our end, that has not been present on this site before!!!
I would be very happy, if you could pay serious attention to this tiny, but very far-reaching annoyance/issue!
I guarrantee you, that there are many more who has been a bit annoyed by this as well, but who decide not to mention it, being afraid to come across picky, grumpy or rude.
I´m not one of those people!
KNOW THIS:
Your layouts looks very good and are well layed out, so "misunderstand me correctly" here...
Your work is greatly appreaciated!!!
...and as for the pedal, it sounds great on the demo!
Just like my Selmer Treble & Bass MK-III amp at full blast!
They really seemed to have nailed it. Top of my future build list!
Christ Neil, relax bud.
DeleteI will re upload the files with normal names once I figure out a way to log on with my laptop so I can upload them directly instead of using photobucket. Right now I'm unable to log on to the site with my laptop, and I can't control the name of the file the way I'm uploading images
ReplyDeleteRequested modified layout has been added
ReplyDeleteAwesome, thanks! this is the first circuit i laid out on stripboard, and i keep using my original one, that has many doubled up holes, standing resistors and all sorts of bad stuff. Nice to have a comfortable layout.
DeleteCool, I hope the layout helps :)
ReplyDeleteLet me know if you build this successfully as it's currently unverified
Sounds neat. I may have to try and find a source for some more Ge's..
ReplyDeleteThe bottom strip that is empty, with those 2 holes isn't for anything, right? Just never seen that before.
Thanks for the contribution Travis.
The bottom strip is there for mounting the board on standoffs. You can just cut that row off if you don't want to mount the board that way
ReplyDeleteCan anyone point me in the right direction for the germanium transistors, preferably UK/Europe but not essential.
ReplyDeleteAlso if you know a good fair priced place for all germanium transistors in general.
Are you looking for tested sets or untested lots? I'm an American so I only really know of smallbear for the tested sets. I buy untested lots off eBay
DeleteChecked small bear and they don't have the 2N2613.
Deleteebay have one unit for £17 ($27) which although im not sure sounds expensive.
Does anyone have any further suggestions, are there alternative transistors that will perform the same?
Any help would be great.
Thanks in advance,
Matt
Find a transistor with a similar hfe/leakage range to the one you're after, then buy it for a reasonable price. The sound is more in the circuit than any other overpriced mojo a lot of the time. $27 for one transistor is insanity.
DeleteLook through this discussion board:
http://www.diystompboxes.com/smfforum/index.php?topic=95208.0
Do you have a transistor tester that can measure hfe and leakage? If so there are a lot of different PNP Ge transistors available on eBay that you could try. AC125, AC128, 2SB175 are some common types you might try.
DeleteIf you need a tested set then the Maestro FZ-1A (or maybe called "fuzz a tort") set from smallbear should work
Verified. I haven't tried the switchable gain boost version yet but i'm sure that will work fine. I upped the 1k q2 collector resister to 1.5k for a little more grit but i'm thinking I might do a silicon version to try and obtain something a little hairier! I stacked it with an Echorec and then got straight into Piper At The Gates. In fact I was wearing a big demented grin. I'd also like to take the time to welcome everyone back, thank lvlark, Mirosol for their patience and guidance and wish Travis, Javi, Zach and Alex all the best.
ReplyDeleteThanks,
Phil.
Thanks for verifying P.Gofton, hope you enjoy.
ReplyDeleteSo one big question. Is that an original Echorec or the Catalinbread?
Bone stock original...Catalinbread...unfortunately i've never clapped eyes upon an original let alone play one. The Catalinbread is great though, so many variables. BTW, any idea what people should shoot for in regards to bias voltages?
DeleteIt works
ReplyDeleteIt works. I only tested it so far with silicon 2n2907. Sounded pretty good actually. The blend doesn't work right with silicon tho.
ReplyDeleteI did the switchable gain version. Sorry guys this is my 1st time using this bloggin stuff or whatever it's called. Ha
ReplyDeleteNice job thanks Gregory. The depth control isn't supposed to work like a blend. It's a variable resistor between the first and second gain stages which works as a gain control
ReplyDeleteSorry bout that I meant gain. I made a replica mxr blue box with the two 741s today. And got the blend on that confused with the gain on this. Anyways the gain feels much better with germanium. And all the gain combos seem to work fairly well. I'll try a bunch of combinations. Feels like the gain is a little bunched at the end of the taper tho. I'll try some different tapers
ReplyDeleteI've made a few with silicon (2N2222's or other lower gain) in Q1 and Q3 and germanium in Q2, bias to like 0.7volts or so with the Q2 collector resistor. i've been adding a germanium diode to the Q2 (base to emitter?) to help prevent the temperature thing with germanium. one of the first ones i made without it, guy said it sounded like someone was slowly turning a tone knob on stage! Anyway, i'm more of a builder than guitar player, but this is a great fuzz.
ReplyDeleteThis was my first ever single pedal build a few years ago, put it in an oversize octo box (like a fuzz face). Now I put everything in the octo boxes, lots of wasted space!
http://www.madbeanpedals.com/forum/index.php?topic=16488.msg156427
Hi, I measured something like 100 transistor with the germanium transistor tester (which thanks to Iviark I built myself). except for the few 2sa12s which were mostly very low leakage with hfe around 30,nearly all of them were of hfe's 150 to 250. it seems that the usable ones most have moderate leakage with hfe's around 50 to 150. am I right? do you think there is something wrong with my measurement. by the way the trannies were Gc301, 2sb75, 2sb54, 2sb175, 2sb176 and 2sa12.
ReplyDeletethanks a lot.
ooops! sorry, "Ivlark", also 100 "transistors"," must " anything else?!
ReplyDeleteI Know this is perhaps a tall order so excuse my cheek, but would it be possible to make a scematic (one board only layout) that uses a 9v power supply? I know there is the daughterboard option but I have less luck the more things that are floating about inside a pedal and was just about to opt for the battery enclosure route -then realised how much more room that will take up....
ReplyDeleteIf you could it would make my day
Sure I can do that. Check back soon and I'll have it done
ReplyDeleteIn the meantime, order some 78L33 voltage regulators!
Thanks Travis you are a star!
ReplyDeleteI have some L78L33 regulators already which I think are the same things.
Again Thanks to the highest.
Hi Travis, Any joy with the 9v Power supply mod?
ReplyDeletehey Mattfode, October wasn't too great for me and I forgot all about this request. sorry for the delay, the new layout is now up
DeleteHi, I got a problem everything works ok when i stay in the first half of the gain pot, on the second half I got self oscillation and its frenquency lowers as I push the gain, does someone got an idea? I alreday triple cheched everything I believe, but....?
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteDo the Transistors need to be leaky like the FZ-1 or can you get away with transistor that have very little leakage?
ReplyDeleteI can't say for sure since I haven't built this yet but I encourage you to experiment with whatever you've got.
ReplyDeleteI'd say maybe .15 - .25mA would be a basic starting point, but even if you don't have that it's worth a try. This is really just a guess based on what you might expect to see from a 2N2613 at normal temp
I'm going to breadboard this and hopefully have some more suggestions
Thanks! do you think the matched fz-1 transistors that smallbear sales would work in this circuit?
DeleteI think I'm going to breadboard this myself and see what I can come up with.
The one from smallbear is an FZ-1A set, and yes it would be the closest thing to this circuit.
DeleteThe MKI sets that I've gotten from smallbear were very poorly selected. Hopefully he does a better job with the FZ-1A set..
Has anyone tried the new layout with the Charge pump and voltage adapter?
DeleteIm having an issue with the caps being to large to fit on the board using stock. What voltage caps are you guys using? Those of you who have built this.
ReplyDeletesince this effect only takes 3V, -3V to be exact, you don't need high voltage caps, just larger then 3V.
DeleteI've got this on a breadboard using the 78l33 and 7660s and was having issues with a constant high-pitched sound. Reading elsewhere on this site (http://tagboardeffects.blogspot.com/2014/08/maestro-fz-1-fuzz-tone.html) I found that pin 6 of the 7660s should be grounded since it's handling a low voltage, and this gets rid of the high pitched ringing for me.
ReplyDeleteI also found I need to replace the the 47uF with something much higher (ended up using 1000uF) to get rid of motorboating.
Sr sorry with my ignorance here is my first DIY Pedal and I dont understand what is the output or where I can find it.
Deletethanks a lot
This comment has been removed by the author.
ReplyDeleteIf I remove the dept pot completely and wire the 22K resistor directly to the 50UF CAP will that give me full fuzz or no fuzz? Sorry I dont have a breadboard to test this other wise I wouldn't ask.
ReplyDeleteI meant if I take the pot out and run the 50UF cap directly from Q1's C to q2's B Would that pretty much give me full fuzz, or would that give me 0 fuzz.
DeleteI built the latest version with 78l33 and it works but I get motor boating too, even with a battery plugged into a 2.1mm jack I get motor boating....weird! Im going to try what another user tried and up the 47uf cap
ReplyDeleteHello. I built this circuit with 78l33 and 7660s and after switching on a loud high-frequency whistle appears. I tried about a dozen different 7660s and 78l33 and the result is the same - a loud high-frequency rumble. Without a regulator and an inverter, it works perfectly with a 3 volt battery. But I really want to power this pedal from a nine volt adapter. Are there any ways to get rid of this noise? Or maybe there is a way to reduce the voltage without these chips?
ReplyDeleteMore likely than not your 7660s chips are counterfeit and just 7660 that have been relabeled. This has been an issue because the 7660s has been discontinued. You can use a MAX1044 instead and see if that fixes the issue.
DeleteThank you. Could you please tell me which chips are better to take on Ebay MAX1044CPA or MAX1044EPA? Is there a significant difference between them?
DeleteAbout that 22uF capacitor on Q1 emitter modification... Take a look at that Selmer Fuzz-wah schematic :
ReplyDeletehttps://www.vintagehofner.co.uk/britamps/selmer/schematic/fwah.html
There is a 25uF at the same spot in the fuzz section of the circuit.
Also interesting because it is a NPN +9 volts circuit... Worth breadboarding and maybe try some kind of hybridization. ;-)
Ok. I know it's an old thread but I just want to tell that I've built the fuzz portion of the Selmer Fuzz-wah wich is basically a silicon NPN, +9volts supply Buzz Tone.
ReplyDeleteI also tweaked the capacitors values because the per design sag of the original circuit lead to noisy decay after each notes. The modified circuit also have a nice harmonic content that makes it sound slightly better to my very subjective hear. I'll give you the ingredients to let you judge by yourself.
To build a wannabe +9 volts silicon NPN Buzz Tone version:
Using the "layout with the requested switchable gain boost mod"
Do the following modifications
Resistors :
- Replace DA-DE 27k resistor with a jumper.
- Replace GB-GE 1k resistor with 41k resistor
- Replace JB-JH 39k resistor with 27k resistor
- Replace KA-KD 22k resistor with 15k resistor
- Replace LC-LG 1k resistor with 2k2 resistor
- Replace PB-PF 1k5 resitor with 220k resistor
- Replace QF-QI 15k resistor with 1k resistor
Capacitors :
* Reverse the polarity of all electrolytic capacitors
- Replace BA-BH 25uF capacitor with 4.7uF film capacitor
- Replace HF-HJ 22uF capacitor with 10uF capacitor
- Replace KE-KI 50uF capacitor with 10 uF capacitor
- Replace NA-NE 25uF capacitor with 4.7uF capacitor
- Replace RB-RH 50uF capacitor with 1.5uF film capacitor
Transistors :
- Replace 2N2613 Ge PNP with 2N5088 (280 hfe min) Si NPN
* Selmer Fuzz-Wah original transistor are BC169C (ECB pinout) but 2N5088 (EBC pinout) are a pin for pin substitute in the present layout if you just mind picking some with a gain similar to the BC169C. That's what I did and it sounds great.
Suggestion :
You may want to replace the boost switch with a jumper between AF-AG as an always ON boost mode...
Try it out. All comments and suggestions are welcome.
Maybe we'll end up with a dedicated schematic for a ( maybe better) definitive silicon version.
By the way, it sounds like heaven with a Rangemaster after it or with your favorite wah pedal. An interesting fuzz in it's own right anyway. Enjoy! :)
Cheers. Little update on my experiment with the "silicon NPN, +9volts supply Buzz Tone". I tried different transistors and found out I get the best from that circuit with hfe 135 for Q1&2 and hfe 265 for Q3. I used handpicked low gain 2n3904 for Q1&2 and kept the 2N5088 for Q3. Lovely amp like overdrive with a hint of fuzziness. The volume is about unity with all knobs at noon. The sag is minimal with the depth at minimum level and becomes "deeper" as turning the knob clockwise. Cleans up reasonably well with guitar volume knob. Won its place on the board. :-)
ReplyDelete