tag:blogger.com,1999:blog-6847048658257278783.post3758137900808512757..comments2024-03-27T15:26:01.893+00:00Comments on Guitar FX Layouts: Landgraff BoostIvIarkhttp://www.blogger.com/profile/08416945174853142251noreply@blogger.comBlogger8125tag:blogger.com,1999:blog-6847048658257278783.post-39282940910910733942014-02-21T10:19:05.070+00:002014-02-21T10:19:05.070+00:00Yes, no problemYes, no problemIvIarkhttps://www.blogger.com/profile/08416945174853142251noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-49142104628890137072014-02-21T07:02:24.394+00:002014-02-21T07:02:24.394+00:00can I just use a 4.7k? its relatively close if I u...can I just use a 4.7k? its relatively close if I use a 5% carbon Anonymoushttps://www.blogger.com/profile/05007350217786442771noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-17616219979738962322014-02-21T06:59:53.630+00:002014-02-21T06:59:53.630+00:00cant find a 5.1k 1/2 watt resistor anywhere... any...cant find a 5.1k 1/2 watt resistor anywhere... any alternatives?<br />Anonymoushttps://www.blogger.com/profile/05007350217786442771noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-56113423230251679672014-02-18T13:49:42.541+00:002014-02-18T13:49:42.541+00:00Swapped the switch and now we're good to go! T...Swapped the switch and now we're good to go! Thanksthebrettmoorehttps://www.blogger.com/profile/05904082462907835796noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-61686299905389514312014-02-17T19:01:41.491+00:002014-02-17T19:01:41.491+00:00If you've wired the switch exactly as per the ...If you've wired the switch exactly as per the offboard diagram then there must be either something wrong with the switch. It can't be the input/output wiring/soldering or you'd also have the problem when the effect was turned on so that only leaves the switch.IvIarkhttps://www.blogger.com/profile/08416945174853142251noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-237640477528053162014-02-17T18:43:25.460+00:002014-02-17T18:43:25.460+00:00Ultra noob question here...I built this last night...Ultra noob question here...I built this last night and used the offboard wiring diagram from this site too. Works like a charm when the effect is engaged but when its in bypass mode the signal is muted. What's going wrong here?thebrettmoorehttps://www.blogger.com/profile/05904082462907835796noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-12317592991455803332013-12-23T20:20:40.205+00:002013-12-23T20:20:40.205+00:00It works fine! It adds nice presence to your tone,...It works fine! It adds nice presence to your tone, the pot is very useable for all his range. It crackles a bit just like the SHO but to my ears this one works better as presence enhancing at lower settings, if you crank it up it's very loud and it goes into distortion well, thank you for the layout.Anonymoushttps://www.blogger.com/profile/07380895582780746866noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-87399138238049204872010-04-18T01:55:26.281+01:002010-04-18T01:55:26.281+01:00Thanks for the update!
MelxThanks for the update!<br /><br />MelxMel xhttps://www.blogger.com/profile/10495407373846331336noreply@blogger.com