tag:blogger.com,1999:blog-6847048658257278783.post1883519906149509998..comments2024-03-29T01:36:12.851+00:00Comments on Guitar FX Layouts: Castledine Electronics The WizardIvIarkhttp://www.blogger.com/profile/08416945174853142251noreply@blogger.comBlogger24125tag:blogger.com,1999:blog-6847048658257278783.post-29491223235237409282021-03-01T09:28:54.658+00:002021-03-01T09:28:54.658+00:00Hi Andy. That sure is interesting. If you could go...Hi Andy. That sure is interesting. If you could go to the forum, you will find a Request part. I'm sure a lot of people would be interested in drawing a layout for this if you'd post it there Marchttps://www.blogger.com/profile/01190587665881779153noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-35718885059122990442021-02-08T22:29:18.605+00:002021-02-08T22:29:18.605+00:00hello !
the Laney Black Country Customs TI Boost...hello ! <br />the Laney Black Country Customs TI Boost schematic was released, can you create a tagboard?<br />https://www.pedalpcb.com/docs/DarkEsbat-PedalPCB.pdf<br />thanksAndyhttps://www.blogger.com/profile/18428117698602506968noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-27207453553707737002020-06-15T23:15:49.247+01:002020-06-15T23:15:49.247+01:00There should be a 47ohm resistor between the 100uf...There should be a 47ohm resistor between the 100uf cap and the 9 volt pad.Dubious Maestrohttps://www.blogger.com/profile/06558123766174016918noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-83450056650694302532019-10-27T08:07:46.325+00:002019-10-27T08:07:46.325+00:00It should be, but I think you have to swap the 470...It should be, but I think you have to swap the 470k between the Treble 2 and the Volume 3 with a 100k to increase the output.<br />I don't know if there something other mistake in this layout.Elijah-Baleyhttps://www.blogger.com/profile/16374916649117645180noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-48308374110248113882019-10-27T02:05:43.142+00:002019-10-27T02:05:43.142+00:00This verified?This verified?Quinn301https://www.blogger.com/profile/10533587464677627924noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-553236005833257252019-07-01T08:33:43.247+01:002019-07-01T08:33:43.247+01:00Those red circles are right the cuts in the copper...Those red circles are right the cuts in the copper trace.<br /><br />And the 47nF are probably connected in rows B and C. When you has these kind of doubts try to take a look at the schematic.Elijah-Baleyhttps://www.blogger.com/profile/16374916649117645180noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-1959994364444288582019-07-01T06:36:29.148+01:002019-07-01T06:36:29.148+01:00I am also a newbie to this... I would appreciate a...I am also a newbie to this... I would appreciate anyone's advice on a few questions about the drawing:<br /><br />what are the red circles with the white dots? cuts in the copper trace?<br />Are the 47nF caps connected to rows A and D? or B and C?<br /><br />Anonymoushttps://www.blogger.com/profile/08767099769719834573noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-72386971538462709432018-12-02T06:52:41.225+00:002018-12-02T06:52:41.225+00:00Would love to build this pedal but can't seem ...Would love to build this pedal but can't seem to sort these transistors anywhere? I am somewhat a novice in the pedal building world so any help would be helpful!Anonymoushttps://www.blogger.com/profile/09855675807527437006noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-59927129203736281602018-06-27T00:28:54.027+01:002018-06-27T00:28:54.027+01:00I'm up and running but getting a large amount ...I'm up and running but getting a large amount of hum running from an ac adapter. Has anyone else experienced this?<br />Anonymoushttps://www.blogger.com/profile/07885848709099122089noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-27782680121176225422018-06-09T00:09:38.905+01:002018-06-09T00:09:38.905+01:00This comment has been removed by the author.Anonymoushttps://www.blogger.com/profile/07885848709099122089noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-46401513720154460242017-11-19T01:36:58.632+00:002017-11-19T01:36:58.632+00:00Looking at the layout, I think we can skip the boa...Looking at the layout, I think we can skip the board J-12 cut.Anonymoushttps://www.blogger.com/profile/05074808768812317716noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-74944323127551088522017-11-12T22:19:51.294+00:002017-11-12T22:19:51.294+00:00Thanks so much ;)Thanks so much ;)Anonymoushttps://www.blogger.com/profile/05074808768812317716noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-24852843241619204672017-11-04T03:02:47.249+00:002017-11-04T03:02:47.249+00:00Yep, swapping 470K to 100K made a very positive im...Yep, swapping 470K to 100K made a very positive improvement for me. Thanks trapiak!Stymie13https://www.blogger.com/profile/06497729693098354702noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-78998250316415011772017-11-02T19:57:25.231+00:002017-11-02T19:57:25.231+00:00MP38A is a solid device and usually comes in highe...MP38A is a solid device and usually comes in higher gain ranges than MP21A. I'd go with MP38A. Both are definitely better than the original when it comes to temperature changes.<br />+mmirosolhttps://www.blogger.com/profile/02400327798106357876noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-45339179035247158392017-11-02T07:40:55.143+00:002017-11-02T07:40:55.143+00:00MP38 vs MP21A as replacement for germanium CV7351?...MP38 vs MP21A as replacement for germanium CV7351?Anonymoushttps://www.blogger.com/profile/05074808768812317716noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-73621624913748982932017-11-02T05:32:05.280+00:002017-11-02T05:32:05.280+00:00That 470k resistor before Volume3 is asking for a ...That 470k resistor before Volume3 is asking for a downgrade then, I think...Anonymoushttps://www.blogger.com/profile/05074808768812317716noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-53745843350591552872017-10-24T17:03:40.634+01:002017-10-24T17:03:40.634+01:00The version i built from the forum also has low ou...The version i built from the forum also has low output volume. I did notice that seems to be the way it is from watching YT vids though.Hozy31https://www.blogger.com/profile/16714771534041521767noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-17536511559818935002017-10-23T20:50:08.613+01:002017-10-23T20:50:08.613+01:00I ordered some 2n1308s.
In the mean time, could I ...I ordered some 2n1308s.<br />In the mean time, could I just drop a silicon npn there ...?Traktophttps://www.blogger.com/profile/15595701243469705272noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-53847060484415557522017-10-23T15:18:30.090+01:002017-10-23T15:18:30.090+01:00Thanks for the layout Zach. I built it and everyth...Thanks for the layout Zach. I built it and everything works but it doesn't seem quite right. Output volume is low just barely reaching unity fully cranked. I used a 130 Hfe MP38A Russian germ for Q1.Stymie13https://www.blogger.com/profile/06497729693098354702noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-51656102195636637292017-10-23T07:32:40.391+01:002017-10-23T07:32:40.391+01:00Nope. The FETs are setup in a mu amp arrangement s...Nope. The FETs are setup in a mu amp arrangement so no worries about biasing the drain of the FET. Zachhttps://www.blogger.com/profile/00044917566185720896noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-64502615794735701282017-10-23T04:21:33.569+01:002017-10-23T04:21:33.569+01:00This is great!
We don´t need to worry about drain ...This is great!<br />We don´t need to worry about drain bias resistors here, right?Traktophttps://www.blogger.com/profile/15595701243469705272noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-32541968598299526092017-10-22T07:51:55.406+01:002017-10-22T07:51:55.406+01:00Cheers man. Enjoy. Cheers man. Enjoy. Zachhttps://www.blogger.com/profile/00044917566185720896noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-64675560982031611612017-10-22T04:19:20.463+01:002017-10-22T04:19:20.463+01:00* you.
Damn auto correct* you. <br /><br /><br />Damn auto correct Dexterhttps://www.blogger.com/profile/08962390415366357301noreply@blogger.comtag:blogger.com,1999:blog-6847048658257278783.post-7700389139246773272017-10-22T04:18:22.057+01:002017-10-22T04:18:22.057+01:00Thanks Zach/rocket88. This is the pinnacle of iomm...Thanks Zach/rocket88. This is the pinnacle of iommi tones from the average amp and I salute toy for the valiant effort Dexterhttps://www.blogger.com/profile/08962390415366357301noreply@blogger.com