Info about the original:
Good Vibrations!
All of the warm, soothing tone you'd expect from a great vintage amp trem with the added versatility of selectable waveform. Designed with the single coil player in mind, this variable amplitude modulator is a favorite among those that want the highest fidelity and smooth performance combined. The Depth control allows you to dial in as much effect as you like, from the slightest hint of mellow sine wave smoothness to fully gated square wave effects. The added benefit of a wide Speed range makes this a very powerful tool for the serious musician. The Vibutron's lemon-lime motif is highlighted by the custom made cherry red Bakelite knobs.
Bon appetit!
Hmm seems like a nice tremolo.
ReplyDeleteI assume it'd be ok to use any common dual opamp (te072,nr5532,jrc4580,...) for IC1 and IC2 ?
IC2 is a single but yes no problem with IC1
DeleteFrantone!? Tremolo?! ICL8038!? When does the hurting stop?!
ReplyDelete;)
But seriously, now I have to get some of these. Do you know of any reason why ICL8038CCPD, in particular, would not work with this?
This thing goes from sweet/mellow to damn near VRP chops. Can't wait to build it.
They're the ones I bought so they better bloody had do! :o) The circuit was tested with expensive ones from Small Bear and the cheapo ones on eBay and apparently they all worked.
DeleteIt does sound damn good and I think I must have bought the 8038s when the thread first appeared on FSB but then it all fell by the wayside as other layouts were being done. But I think they could be really useful ICs to have and experiment with for anything using an LFO. As usual I got 10 :o)
Excellent! Chips ordered. I can't resist a good tremolo. I think I've built every single one from this site except for one that had some odd component... can't recall exactly which one. I've built every one that Madbean, Guitarpcb, and musicpcb have put out as well :/
DeleteWow... moment of clarity.
My name is Heath.. and I'm an addict.
You and me both matey!
DeleteOne thing I should add before you build it is to check that the contacts on the Waveshape switch behave as shown in the switch diagrams before soldering it up. The way it is drawn requires 2 & 3 and 4 & 5 to be made in the centre position. If that isn't the case with the ones you buy and instead 1 & 2 and 5 & 6 are made in the middle position, then swap over the poles so:
ReplyDeleteLug 1 becomes 4
Lug 2 becomes 5
Lug 3 becomes 6
Lug 4 becomes 1
Lug 5 becomes 2
Lug 6 becomes 3
I'm so glad you posted that. It caused me to check my switch stash and I'm fresh out of on/on/on anything.
DeleteIt's in my mind at the moment because it came up recently in the Fulldrive thread, and I'm sure they'll be people have problems with their build simply due to the fact there is no norm, and both contact configurations may be supplied. So it's a bit of a crap shoot if you don't check.
DeleteI definitely prefer on/off/on when it comes to layouts and support!
I think I kinda need to build this. I've been wanting a good tremolo for way too long. I like my tremulator clone but don't dig the weird volume boost/cut depending on where the depth is set
ReplyDeleteDo it, I think this is one of the nicer sounding ones I've heard, and it always gets good reviews. Plus it's $375!! :o)
DeleteBasically the guitarist from Clinic has convinced me that I need a good trem :P
ReplyDeleteI can't believe they're charging $375 for this! You'll shudder but I paid $380 for my Jerms FZ-1. That pedal is my favorite though, and if I showed you a gutshot you'd see why I bought it
Just saw it on DiscoFreq's site. Very nice.
DeleteGot my 8038`s today so got this built tonight with mixed results. Firstly I`m getting a tremolo effect but only on 1 of the wave settings, as my switch was inverted to the example on the layout I thought I`d screwed up the wiring, triple checked it but it appears correct. If I`m understanding the wiring correctly sw5 is the common and the waveform changes by connecting it to either sw1, sw3 or sw6, sw5 & sw6 give tremolo, sw5 &sw1 or sw3 give unaffected signal. Fast switch gives unaffected signal when the connection between the wires is made but tremolo when the connection is broken. I`ve had a quick look at the schematic and the only thing jumping out at me is it shows pins 6&8 of the 8038 connected to 9v and the layout has only pin 8 connected. Will give it another look tomorrow.
ReplyDeleteWhen he tested it, the circuit didn't work when 6 was connected if you read his last post, so he said 8 only in the end. Are you sure you have the right on/on/on switch? Some work mirrored so the opposite pole changes state first, and if that was the case you'd need to connect 1 and 5 with a link, 2 would be the common, and the connections would be to 3, 4 and 6
DeleteDifferent on/on/on switching
If you bought more than one, use your multimeter to see which pole changes state first.
yeah the switch is mirrored but I wired accordingly, I`ve even desoldered the switch and connected the common to the individual wires using a crocodile lead and still only working with 5&6 connected. will check my voltages later.
Deleteonly just noticed I`ve put in a 100 uf cap instead of a 1000uf, and no 1watt 10r resistors so used 1/2 watt.
1000uF is overkill IMO, 100u is fine there and 1/2W is fine for the 10R as long as it doesn't burn up. Personally I'd use a 100R there instead of 10R and just stick to 1/4W.
DeleteHow many ICs did you get and did you socket?
got 5, yes socketed and tried them all, they seem suspect tho`, only getting 7.2v at pin 8. if I take the chip out I get 9v at pin 8 on the socket.
Deletedamn hard to fine icl8038 ,i love this sound
ReplyDeletehttp://www.ebay.com/itm/260691257816
DeleteI have a nice tremolo output with the fast switch, speed and depth controls working. All three waveforms are working as well with the DPDT on/on/on switch. The problem I'm experiencing is a very loud and nasty LFO ticking sound, similar to a Vox Repeat Percussion. I've been looking at the PCB of a real Vibutron and that missing connection to IC3/Pin6 bugs me. I have been trying different ways to use Pin6 w/o luck. I know that KindaFuzzy says not to use Pin 6 with his schematic but it still bugs me that Pin6 is connected and working on an original design. BTW, the original design uses an ICL8038CCPD for IC3. Still troubleshooting...
ReplyDeleteFor reference, KO Amps has posted a photo gallery of a disassembled Vibutron;
http://bit.ly/1oyz3z8
Yes it is peculiar and it's there for everyone to see that 6 is also connected to the supply and looking at the datasheet that's the V+ pin so you would think that connection is compulsory. I've just looked over the PCB and the only thing I can see that is different is that 7K5 in my layout looks more like a 1K5 on the board.
DeleteYes... I also noticed that. I tried putting a 1K5 there with and without Pin6. The only thing it did was increase the speed rate.
DeleteSoooooooo very close to calling this one verified. The loud LFO ticking sound was eliminated after removing all components off the breadboard and soldering everything onto a strip board. One of the keys to getting this sound right is fine tuning the 100K trimpot to find the sweet spot. Almost everything is working as expected except;
ReplyDelete1) When the Square Wave is selected, the Fast Switch doesn't do anything (but it does work for Sawtooth & Sine). Since the original Vibutron doesn't have a fast switch and never shorts Pins 7 & 8, I'm wondering if it "would" be functional?
2) I can't tell much difference between Sawtooth & Sine except on the higher speeds. However, there is a dramatic difference between Square.
I'm not worried too much about Pin6 anymore because I found another project using a ICL8038CCPD and it did not have Pin6 connected either.
This thing sounds phenomenal as is... even without everything working :^)
Still plugging away...
Well as you say, the Fast switch is an added bonus based on the IC notes rather than the actual Vibutron and so how it works is always going to be a crap shoot. If it doesn't work in some settings then I can live with that because it doesn't matter to the actual circuit. Square is always more extreme, and as the other waveshapes can sound very similar in some settings I reckon that is verified if you concur.
DeleteDid you think it was better with a 7K5 or 1K5 in there?
I concur. To me, it sounds better as is with 7K5 because I like the option of having the slowest speeds available. Using 1K5 does have a benefit though because at the highest speed setting, it gives a metallic, chorus, shimmering sound.
ReplyDeleteOn a side note, one thing I accidentally discovered... if you place a jumper from IC3/Pin3 to IC3/Pin9, you get a "pseudo reverse gate" sound. Very different. The downside is you forfeit the Square Wave.
re: Similar sounding Sawtooth and Sine on the Vibutron, I found this online discussion;
http://bit.ly/1nBVxSQ
OK I'll tag it and add a modded version with a switch to swap the resistors and add the link. It can be an option then.
DeleteThanks for you work on it buddy
Hi,
DeleteI've built this pedal today using 100uF, 100R 1/4W and 1.5K.
It works but the slowest speed is not as slow as you hear in the video.
I've double checked values and connections and everything matches the layout.
The Peddler said above that the slower speeds weren't available with the 1.5K resistor, so you want to swap it for a 7.5K (or some value around that).
DeleteI've tried a 7.5K but it didn't get much slower.
DeleteThe slowest speed I get is almost 2/3 if not half of the pedal in the video.
Socket it and try increasing the resistor value
DeleteI was so amazed at the great sounds that I did not even notice the speed is different from the one in the video clip. After comparing... yes... my build is a bit faster. I'm breadboarding a 2nd one now. Replacing the 7K5 resistor with a different value is too limiting (no range). Replacing the 7K5 resistor with a pot just makes things sound too funky at the Min/Max settings. A 2nd DPDT on/on/on switch with three resistor values might be the cure? I really, REALLY like the jumper option from IC3/Pin3 to IC3/Pin9 and I'm testing different ideas for that as well. I should have more info after the weekend.
DeleteFor those interested, I have uploaded a video clip of current breadboard tests for the Vibutron w/7K5 resistor. The audio track has Sine/Triangle/Square with Slow/Medium speeds. The new Pseudo Reverse Gate Effect is towards the end. I don’t have a video camera so I just added some random images as filler.
Deletehttp://youtu.be/ER7DM929YbM
Sounds cool. Thinking about it the 7K5 looks like it's a minimum resistor for the Speed control, but the 220n is described as the Timing Capacitor in the datasheet, so it may be worth swapping that out to see how it affects the slowest speeds
DeleteFantastic! THANKS! That's the missing puzzle piece for me. I substituted a 1uF for the 220n and it's really S L O W now. The Fast switch has no effect now but that's beside the point because it can still function as a Fast switch by using the old 220n in it's place. Does that make sense? Maybe use the Fast switch to select between a 1uF and a 220n. Still testing. Must get sleep sometime... Geez!
DeleteYes I reckon that's the way to do it, get rid of the non Standard fast switch and instead use it to swap caps. I'll update the layout
DeleteAfter some more tinkering, I decided to go with 2uF on the Fast Switch. I used two 1uF in parallel and that provides a complete range of speeds from insanely slow to maniacally fast.
DeleteBreadboard tests video Part 2: w/2uF and 220nF capacitors on the Fast Switch;
Deletehttp://youtu.be/4KslUHnxyYs
Yes there's plenty of range there now. That reverse gate effect is cool too
DeleteSo, the layout that we have now is working? Or does it need to be fixed in some way? Thank you for all the effort!
ReplyDeleteYes it's good to go as it is. I may add a switch for the resistor discussed above, but you can still start populating the board, just omit the 7K5 for the time being
DeleteSo do we still leave out the 7k5 resistor. Also speed 3 to ground, empty ...? I couldn't find any lm741's, would a tl071 work in there instead? In the layout by that 3 spot jumper it shows the cut in to 2 different places on the blank board and the populated board. It doesn't look like the cut would effect anything, but it made me go cross-eyed when i was trying to populate the board :) Thanks for your help!
ReplyDeleteNo you want the 7K5 resistor in, if you don't see it mentioned then there is no connection so you can ignore Speed 3, and yes the TL071 should be fine
DeleteThe world conspired against me on this build. I had to go over it several times and found a personal mistake every time, but everything is working right now, and it is an amazing temolo. After getting it all squared away, I thought I only had one working setting on the waveform switch, but after dialing in the 100k trimpot, they're all there. You guys are awesome!
DeleteDudes, can you please help me? I'm hearing the lfo doing its thing and everything, but the signal is dry....the guitar literally does not "tremolo", but all the switches, knobs, do something to the lfo...but not getting the tremoloed sound. What can i check please? I've build over 60 pedals and all worked from the start...this is the only project i'm having trouble with. Please :)
ReplyDeleteI rebuilt it from scratch and will try again today...i also tried wiring the on on on switch accordingly because it is mirrored...also tried every combination, nothing made it tremolo...But comparing it to my previous build it looks identical...so either a component was faulty that does not "take" the guitar signal and tremolo it, or I dunno. (i checked the traces, cut in between the traces for solder bridges...etc) But as i said, the LFO was working , so my guess is that it is a faulty component.
DeleteThis is starting to get ridiculous...never should have doubted myself. IT does exactly like the first build..exactly, the LFO tick is heard, all the knobs do something, the switches modifies the speed/signal accordingly in the ticking...but still a dry sound. Am i missing something? It's clear to me now that i did nothing wrong at the circuit,because it is identical, and i made it with a fresh start alltogether.
DeleteThis comment has been removed by the author.
ReplyDeletehey guys.. ive just fin this build .. it all works as said but the lfo is quite audible . any one else face this ? or suggest a way to remove that noise . could it be - the ic1 i used AD822 instead of TLC2262 . its supposed to be a proper pin to pin replacement
ReplyDeleteappreciate any help
thanks
Some ideas to try (in order):
Delete1) These are the exact part numbers I used;
IC1: TLC2262IP
IC2: UA741CP
IC3: ICL8038CCPD
MOSFET: 2N7000-D46
2) Check for a short between INPUT and IC1 PIN3
3) Try to rearrange wires away from any 9V areas and all board components - helps with LFO issues sometimes. I always use shielded cables from INPUT to board and from board to OUTPUT
4) Try it with a battery vs. with a wallwart
5) As mentioned in a earlier post, the key for getting this to spark was fine-tuning the trimpot
I still get a slight LFO tick but only when selecting square wave. Of all my pedal builds, this is probably my favorite one. Incredible sounds! After building it, I've spent all my available peddle-building-time working out some mods for this one including different waveform outputs. Stay tuned.
Hey, could you please give me some pointers what to do with my build? Built it TWICE from scratch a second time around...nothing works,as the first time. I've wrote something a few posts up maybe that is enlighting. Tnx!
Deletethanks Peddler , ill try through those.
DeleteRazvan ... i had the same till i adjusted the trim pot ..then all the effect(wet) came alive.
Hmm, i tried fiddling with it in both builds, it does something, but still no "wet". I have a theory: could it be the fact that(out of curiosity i measured the trimpot, it's the most common cheapo blue/white combination trimpot), the trimpot has 82-88-89k max, and maybe, just maybe, the sweet spot would need let's say an exact 100K measured trimpot, maybe that works ast 92-95K exactly...since mine is just 82-88K to start with, the values are"not there". Could this be it?
Deletehey , thanks peddler ..went through yr check list .n got it going but in a diff way .
Delete1. IC 1 is AD822AN , IC 2 & 3 are the same as yours Mosfet 2N7000 D18
2. no short between input and IC1 Pin 3
3. Rearranging wires helped ..but still ticking ..just bit softer
4 same with batt or powersupply(fuel tank)
then i rebuilt it with sockets to change ICs and used shelded wires as u mentioned
nice one .. didnt kno of that bef .. thank you
then between various tries to reduce clicks ... i put an led from IC3 Pin 9 ..and the clicking is negligible .. sounds great and useable now. also shows the tempo in blinks...ofcourse that kills the Sq wave. so i setup a rotary switch such that on Sq wave the the led goes off ...it clicks but on Sq wave its harder to hear ..
I also did the IC3 pin 3 to pin 9 short.. pseudo rev gate on a spdt... killer
last check tomo with other pedals in chain ..mainly gain type ..
thanks all for your work and help
Hitech
During the rebuild whle trying other ICs i noticed the ticking is on from 8038 even without any other Ic present on board replaced the 8038 and still same .. maybe IC is iffy..?
Deleterazvan .. my trim is set about 85 depending how measure ..and the pot reads 97k total.
try an ext 100k to check or a larger value trim if u have..but well below 85 it still has effect only very soft
This comment has been removed by the author.
DeleteThanks for the reply...Unfortunately, that did not solve anything. The LFO is present,etc...ticking. Still a dry sound.Oh well, I'll let this one go and that's it. Will build another one for the man. Thanks.
DeleteAre you sure your 8038's are ok? People have obviously had success with this build so if you're had a couple of failures, the 8038s are a common denominator and a very likely cause of the problem
DeleteThanks for the reply IvIark. I have dropped the project altogether and talked with the person to build another trem model, which worked as always, from the first try ...oh well :) Thanks anyway!
Deletehey ,
Deleteupdate...the trem still had a clicking even after the last changes...soft but audible when amplified loud ..
i found removing the 10k between IC3 pin9 and IC2 pin 7 helped a lot..not sure what the resistor was for but it didnt change the sound or functions .. if anyone can explain its purpose please..
then a 4.7u cap frm IC3 Pin 9 to Gnd absolutely removed the clicking ,, even on sq wave and the rev gate effect... found no loss of highs in the tone. keeping it this way for now.
any thoughts...
hitech
2 new things i added ..
Delete1 taking the tempo led source form ic2 pin 6 gives u tempo and waveform as the led swells and dips .. even the rev gate . IT is INV of audio signal but works.
2 to get the max out of each waveform i used 3 VR s- 100k each, through the rotary switch ( wave select switch) to set each to where they respond best. gives better response to the sq wave .
cheers
hitech
That's some GREAT news! I know what I'll be doing this weekend ✅
DeleteI'm really looking forward to get rid of that clicking sound and those fine tune pots look like a good mix.
yeah .. do let kno how it turns out.
Deleteu may need a smaller cap , i went up in capacitance till the ticking was gone n i believe in your make its softer as it only shows on Sq. wave.
Thanks for this info Hitesh
DeleteBeen over this build many times. Maybe someone here will know what is up. I'm getting a significant cut to the signal as well as tone cut to the highs. All functions are working with the trimmer adjusted just right. The switches all work. The one thing that seems a little weird is the 100k from ic2 output is dropping 3/4s of the signal on the way to the gate on the mosfet. Any ideas on where to look? I have tried swapping out the mosfet and ics and have the same problem. Thanks in advance, i will keep looking into it in the mean time
ReplyDeletehi all ..aft a lovely 2 months with this pedal its suddenly beginning to distort the signal if i play a chord or even 2 notes together .. like input overload .. i have a audio probe .. n found the signal clean till the 2n7000.. and breaking up aft . have replaced al IC s and mosfet .
ReplyDeleteits more pronounced at full depth
any help .... pls :(
I have the same problem from the beginning. Used a scope to check the waveforms and they are good. As usual for this chip, the square is much higher amplitude than the sine or triangle. Interestingly, the square does not seem to distort the audio signal, probably since it is just turning the MOSFET on or off. If I drop the bias on the MOSFET to shut it off, the guitar signal going through both halves of !C1 is equally clean. Everything works exactly like it is supposed to except for some distortion with the sine or triangle driving the MOSFET. I also replaced the MOSFET and hear no improvement. The breakup is not to bad when the blend pot is less than halfway, but is quite noticeable when more of the vibrato signal is present. Since the MOSFET is just acting as a variable shunt to ground I find this confusing. The MOSFET has to be injecting the distortion. Never had any ticking or other problems. Any idea of what could be wrong?
Deletei think i go for a rotary switch, i like it original :)
ReplyDeletebut... as far as i can see it seems like switching will be SW5 to SW1, SW5 to SW3 and SW5 to SW6 or am i wrong? leg 2, 3 and 9 on IC.
pedal sound great on YT vids, i have high hopes for this one :)
I had a bit of a job getting this one going (wired the switch incorrectly first time round). The square wave sounds good but the other settings have virtually no effect whatsoever, any hints?
ReplyDeleteif its of use to anyone in most frantone pedals the 10r 1w resistor is connected directly to the power jack along with an 11v zener diode, zener positive to negative lug and zener negative to positive lug.
ReplyDeleteproviding polarity protection, cureent surge protection and excessive voltage protection all in one easily replaceable crowbar.
for anyone having issues with ticking i found that a non polar 1uf cap between pin 8 and 9 of ic3 completely eliminated it. got the idea here: https://sites.google.com/site/flofxdiy/deticking-lfo
ReplyDeletetheres some useful stuff for debugging lfo ticking in general to.
It works very well! No more ticking. Thanks!
Delete