Friday 24 July 2020

Frantone Lo-Tone Classic Fuzz

From the source:

At last... a classic fuzztone for bass!  This transistorized beauty uses germanium diodes for soft knee clipping and actually boosts the bottom to give you awesome sustain with rich creamy fuzztone.  Wonderful overtones and plenty of thump to boot.   








17 comments:

  1. Built the circuit and got no sound. Just did some comparing to the schematic and the 10k resistor connected to Fuzz 1 is down one row too far, it should be connected to ground on row G. Also the 1uF cap at the bottom of column 9 should be a 1nF cap. Thanks for the post, always look forward to trying some bass pedals. Will update when I get a chance to make the changes to my build.

    ReplyDelete
    Replies
    1. good catches. changes made and updated layout

      Delete
  2. 10k is still in row C to F instead of C to G? Should be C to G like Servant07 said (?)

    ReplyDelete
    Replies
    1. shows up correctly when I look at the layout on the site.

      Delete
  3. Would a 12v zener work in place of the 11v that’s called for?

    ReplyDelete
    Replies
    1. It's just over voltage protection - 12V would be fine but you can just omit it too

      Delete
  4. Built to the layout above. Everything works. What I have learned is the it doesn't like an active bass. If I had the fuzz cranked all the way with an active bass it would gate/cut out. If you turn the bass level down on the bass it helps. Also very sensitive to volume control whether it be passive or active bass.
    It's also a very bass heavy pedal. The tone control does a little but not a lot. I should add that I didn't have any 10k resistors so I used 11k in place. Not sure if this has a lot to do with it , I am very new to building pedals. I tested on the bench with headphones through a tascam GB10.
    All that said it seems to work well with a passive bass. Thanks for another great layout for us bass players. Back to my rabbit hole.

    ReplyDelete
  5. tone to to volume 3..
    i suppose you mean tone two ;)

    ReplyDelete
  6. I watched Fran Blanche repair one of these on YouTube.
    https://www.youtube.com/watch?v=wy8LSYtHXdg
    At 19:30 she whips out the schematic and it has two more cap than your layout. She has a 1nF from B to C on Q2 and a 1uF cap in series with the 10K that goes to Fuzz 2.
    Thanks for operating such a cool and informative website.

    ReplyDelete
    Replies
    1. cheers man. the schematic i had didn't have those. made the corrections and updated the layout.

      Delete
    2. Your previous layout already had the 1nf on B and C of Q2. Now your layout has two of them where there should be only one.

      Delete
  7. I built this to the original layout and it didn’t really sound that good. I made the changes above without making a new board just to test it out. It sounds so much better now. It’s been moved from the scrap pile to the box it pile, lol. Thanks for updating and for everyone that continues to contribute to the excellent site.

    ReplyDelete
  8. Built this updated layout, works great!

    ReplyDelete
  9. Hello, I would like to know where I connect the wires of the Switch?
    Can anyone tell me where on Veroboard I put it?

    ReplyDelete
  10. The switch is wired like this:

    https://tagboardeffects.blogspot.com/2012/02/offboard-wiring.html

    The input wire is shown on the Classic Fuzz board layout, and the output wire goes to Volume 2 lug as per the notes at the bottom of the layout.

    ReplyDelete
  11. Built on today - tried it with MPSA18s and it was too much - replaced them with BC108Cs instead (Hfe of 400 - roughly half of the MPSA18s) and it's great.
    It's got a TON of bass though, so might shave some off.

    ReplyDelete