Tuesday 13 October 2015

EarthQuaker Devices Talons

Info about the original:
The Talons is an extremely versatile high gain overdrive that serves up the full range of gain from transparent boost to heavy saturation, and all points in between. Unlike all our other overdrives, the Talons was not designed to emulate any specific sound or era. The presence control gives you a wide range of top-end contour and the active 3 band EQ allows you to sculpt your tone to perfection. The Talons can be powered at the standard 9v for a warmer amp-like tone or at 18v for greater headroom, more volume and a brighter, stiffer grind.


44 comments:

  1. Nice job Alex !! When you say "Caps rated 25+", does it mean that all caps (non polarized too) need to have a voltage value > 25 volts ? Thanks !

    ReplyDelete
  2. Alex, is there any way you could post larger versions of the layout images? At 320 x 289 the component values are sort of blurry, I just want to make sure I'm reading things correctly. Thanks for all the nice layouts, there's a lot of cool new stuff I'm looking forward to building!!

    ReplyDelete
  3. 25V+ is only for the polarized caps.
    The others are usually much higher.
    If you click on the layout it gets bigger (i'm afraid won't get any bigger than that).

    ReplyDelete
    Replies
    1. The electrolytics need to be rated at least 25V if you choose to use an 18V power supply.

      Delete
    2. Merci ! I'll try this one. And thanks in general for providing so much happiness !

      Delete
    3. BOC,
      My general rule of thumb for pedals and caps are...
      If I am making a fuzz or anything that just uses 9v power supply, I will get caps at 16v or higher. And if the power supply for the pedal is 15v or 18v, then I look for 25v caps or more... Keep in mind that the more voltage a cap is rated, the bigger the size cap so try and get the lowest voltage (25v) if you can.

      Delete
  4. This comment has been removed by the author.

    ReplyDelete
  5. OK, I had been choosing "open in new tab" which just opened the preview image in a new tab, that's why it was so small. User error, sorry :-P

    ReplyDelete
  6. No problem. Glad it's solved.

    ReplyDelete
  7. I love seeing all these new layouts on the main page again!!!

    ReplyDelete
  8. what does CLR resistor mean?

    ReplyDelete
  9. It's the current limiting resistor. Usually 1-5k. This is the resistor that controls the brightness of the led you have for indicating by the effect is on/engaged.

    ReplyDelete
  10. It's the current limiting resistor for the LED

    ReplyDelete
  11. It's the current limiting resistor for the LED

    ReplyDelete
  12. Alex, the way you always manage to keep pots leads close together is awesome and makes off board wiring so easier that's great

    ReplyDelete
    Replies
    1. Thanks!
      When I draw a layout my two main concerns are pots wiring and caps sizes.
      I get stressed quite easily and when I build a circuit I hate having to struggle with wiring or trying to fit components in tidy spaces. I know some layouts could be a bit smaller but I prefer to make them as easy to build as possible.
      Glad you like them. :)

      Delete
  13. Pic of the board I just cooked up. I'll box it tomorrow and make a demo. Thanks for adding this I love the earthquake pedals.
    https://www.facebook.com/BuiltbyRyan/posts/888885497825500:0

    ReplyDelete
    Replies
    1. Dam you ran faster than me !! Well done ! Mine is in debbuging process !! How does it sound ?

      Delete
    2. Sounds awesome! Great range of tones. I'll get a long demo up later I have to go to work. Here is a little clip I threw up.

      https://instagram.com/p/81OvetBTRu/

      Here is a pic of it boxed

      https://instagram.com/p/81MVtThTdH/

      Delete
    3. The insides, sorry forgot...

      https://instagram.com/p/81PueGBTTv/

      Delete
    4. Where did you get those little plastic covers on the back of your pots?

      Delete
    5. http://www.taydaelectronics.com/potentiometer-variable-resistors/rotary-potentiometer.html

      When you buy the alpha pots from Tayda they are included. Great deal! mammoth electronics sells them too, they have really nice colorful ones they just cost$$$.

      Delete
  14. Hey Alex, I built this one a little after it was posted on the forum (I forgot to comment on it there) and this one is easily one of the more versatile overdrives out there. Thanks for the layouts, they've been spot on.

    ReplyDelete
  15. Liking this one. Its quite similar to my Madbeean Chunk Chunk but with slightly more bass and sustain. Another great pedal!

    ReplyDelete
  16. Would you be able to advise please on how much replacing the 3M2 resistor with a 3M3 would affect the sound? I cannot find a 3M2 anywhere.
    Thank you.

    ReplyDelete
    Replies
    1. not at all! even a 1M will not change the tone. it's a pulldown resistor. in fact most effects use a 1M resistor in that place...but anyway.use that 3,2M

      Delete
  17. This seems to get a really nice sparkly clean tone when drive pot is at zero. Maybe this could be a good alternative to the detox eq. in order to "clean" an already cranked amp with that powerful tonestack...

    ReplyDelete
  18. Do you have the actual schematic of this thing?

    ReplyDelete
  19. Ok so I just built this thing, and I'm still pretty new to building pedals (this was my first vero board build). So I plug it in and everything works fine but it is super quiet and the volume drops when it's engaged. Please help. Thanks

    ReplyDelete
    Replies
    1. Did you ever get any answer to this? I know I'm a but late to this post but I'm new to this shit still and wanted to get any insight before I started that'd be of interest or help. Thanks

      Delete
  20. I just wanted to say, kudos to Alex for this layout. It's so neat! IMO neat board > compact board. Thanks again.

    ReplyDelete
  21. I build 2 of this beast and on the 2 pedals I've a problem of hiss bypassed and engaged, like there is a filtering problem of DC. Nobody get this problem?

    ReplyDelete
    Replies
    1. Ever get any answer to this? I'm attempting this soon. It's gonna be my first.

      Delete
  22. Does anyone know where GAIN 3 goes? Is it to GROUND?

    ReplyDelete
  23. This diagram shows a 4.6k on gain 1. PCB layout page says 4.7k

    ReplyDelete
  24. Hi everyone, I just built this pedal and it works great. I am giving it 9v but is there a solution for the led brightness not to change with 18v? I am thinking about some transitor or ic trick, but I didn't catch any solution :/

    ReplyDelete
    Replies
    1. never thought about that before. maybe a zener diode would help keep the led limited to a certain range or specific voltage...?

      thats not necessarily an answer, im just thinking out loud...

      Delete
  25. How could I make it less fizzy? Different clipping diodes?

    ReplyDelete