Friday 9 November 2012

Black Arts Toneworks LSTR

Info about the original:

The Black Arts Toneworks LSTR is the red-headed step brother of the Pharaoh. The LSTR provides even more fuzz and mayhem than its brother with the swell of low end you would expect from any Black Arts pedal. This Toneworks beast uses a uniquely interactive tone control circuit allowing for a traditional tone control as well as a control for scooping the mids right out of your signal. This tone circuit allows you to achieve Russian style scooped mids with a smooth attack or huge wide-open fuzz and perfect string definition with ease. The LSTR is hyper-active gain in a box that could get you sent to bed without dinner. 






28 comments:

  1. Sooo... It's a black russian with modified clipping and cap mixing :)

    I think i should give this one a go at some point.
    +m

    ReplyDelete
    Replies
    1. And Darlingtons! I thought it sounded a bit gated in the clips.

      Delete
    2. One should get the same gating with 2N5089s :) If i'm building this, it'll need sockets. Somehow i feel that this might sound the best with BC550Cs :)
      +m

      Delete
  2. That demo sounds awesome. I think I'll have to build this one

    ReplyDelete
  3. I loved the Pharaoh, going to have to build this too :)

    ReplyDelete
  4. I don't have any non polar cap at the 1uf range... is there a good source for them or can I just use electrolytic and tantalum capacitors? if so which was so the negative side go?

    ReplyDelete
    Replies
    1. i dont see a 1uf cap in this build, only cap I see with a 1 value is a 1n.

      Delete
    2. dexxyy is correct, although an "n" is just an upside down "u" :o)

      Delete
    3. A: I'd like to thank Dexxyy for a quick replay...

      B: I had a couple of tabs open and typed this in the wrong one... ^_^

      Sry for the stupidity. ^_^

      Delete
  5. tayda on ebay sells them (1uf boxed film caps).

    http://www.ebay.com/itm/10-x-1uF-100V-5-Polyester-Film-Box-Type-Capacitor-/260848704784?pt=LH_DefaultDomain_0&hash=item3cbbcb5d10

    ReplyDelete
  6. Tag.

    Didn't even try anything else in there. MPSA12s on this are not as bad as one might think.

    Interactivity between scoop and tone pots is probably the best thing is this. Well. I'm not impressed, though it is an ok BMP derivative.
    +m

    ReplyDelete
  7. when i turn the tone to full, most sound goes away and i get a thin, sputtery kinda thing. sounds nice and full with tone all the way ccw, lose all sound around half, sputtery thinness at full. any ideas? btw i used 2n5089s, but I'm sure that doesn't matter. thanks guys!

    ReplyDelete
    Replies
    1. Check your soldering on the Tone and Scoop pots and also the tone stack components on the board, 1n, 10n and 68K. Sounds like a bad joint could be to blame.

      Delete
  8. Can anyone tell me where is "OUTPUT" on the schematic please? I dont know where i should set it. Thx for answers

    ReplyDelete
    Replies
    1. It says under the layout: "Volume 2 to output". That means volume pot's lug 2 is the output.
      +m

      Delete
    2. Oh, I was blind :D Thank you

      Delete
  9. I've just made it whole .. and it doesnt work for me. Only thing what it can do is tune the citizen radio :D... May I ask you for the original schematic please? It will help me a lot.

    ReplyDelete
  10. i have an original lstr built in 2011 if anyone would like some gutshots. it's laying on the bench now as i just finished wiring in a different led, as i must've stomped too hard last gig. broke a lead. FWIW...this is a serious sounding pedal, not as gated as suspected in earlier post. very responsive. best muff variant i've ever played. been on my gig board for two years. th megalith mught replace it soon though once i finish that build

    ReplyDelete
  11. Anyone have any ideas why my tone and scoop pots are working as reversed volume controls and my volume is working like a tone? Any help would be greatly appreciated.

    ReplyDelete
    Replies
    1. Nevermind, built a new board and it works perfectly.

      Delete
  12. This is one of my favorite builds but I was wondering how to add a diode clipping switch like the Pharaoh.

    ReplyDelete
  13. Hello, I built this one. It works pretty good. But i have one issue. With 9V battery it works. But when i plug in DC jack into it, it doesnt work.. even LED doesnt light. So i guess there is something wired badly inside on DC connector. Can anybody tell me how it should be wired? I wired it like this http://i42.tinypic.com/2q8my5z.jpg Same as pedal i wired before and it worked... Can there be some problem with polarity? or with grounding? I'm lost.. I will appreciate any help. Thanks

    ReplyDelete
  14. Really no any wiring to output from board? Only one from Volume pot?

    ReplyDelete